Bedienungsanleitung Megasat Seaman 45 (Seite 7 von 23) (Englisch)

479172

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Selecting the locationPreparing for the installation

Install Tools and Materials

1. Verication of the Vessel’s Power Supply.

2. Verication of the Satellite Receiver and IDU’s attachment and

the electricity supply

3. Procedure of the satellite’s attachment and installation.

Warnig!

The Seaman antenna system is designed for simple installation and setup. However,

the following list of equipment or items should be available during installation of the

Seaman antenna.

Determine the optimum mounting location for the antenna radome assembly. It

should be installed where:

Perform a through site inspection on the roof for the antenna to be mounted.

If these conditions cannot be entirely satised, the site selection will inevitably be a

“best” compromise between the various considerations.

• Electric drill and drill bits

• Socket wrench

• Silicon sealant

• Fastener suitable for specic application

• Conrm that the vessel’s power supply is 12VDC~24VDC.

• Attach Satellite Receiver and IDU in the interior of the vessel or the trunk.

• Connect the power of Satellite Receiver and IDU.

• Once the power of Satellite Receiver and IDU is veried, it conrms that

both Satellite Receiver and IDU are working normally.

• Attach the satellite on the at surface area of the vessel’s roof.

• Connect each end of the Coaxial antenna cable to the satellite’s

terminal and the IDU.

• Connect the IDU and the Satellite Receiver box together through

the coaxial cable.

• Make sure that the satellite is working normally, once the power

is supplied.

• Turn o the power when attaching or detaching the antenna.

• Make sure that the attached satellite is xed on the at surface.

• When attaching, ensure that all the products are adhered properly.

• Ensure that all the cables are connected properly.

1. The antenna has a clear line-of-sight view to as much of the sky as is practical.

Choose a location where masts or other structures do not block the satellite

signal from the dish as the vessel turns.

2. The antenna is at least 5 feet away from other transmitting antennas (HF, VHF

and radar) that may generate signals that may interfere with the Seaman anten-

na. The further away the Seaman antenna is from these other antennas, the less

impact their operation will have on it.

3. Direct radiation into the antenna from vessels radar, especially high power

surveillance radar arrays, is minimized. The radome should be as far away from

the vessels Radar as possible and should NOT be mounted on the same plane

as the vessels Radar.

4. The antenna radome assembly should be rigidly mounted to the vessel. If

necessary, reinforce the mounting area to assure that it does not ex due to the

vessel motion or vibration.

1. The antenna must have a clear view of the sky and the horizon at all the direc-

tions to avoid blockage of the satellite signal.

2. The antenna should be on the top of the vessel.

Good

Location

Best

Location

Poor

Location

Figure 2-2 Selecting the location

ENGLISH ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Megasat Seaman 45 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Megasat Seaman 45

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info