551340
16
Zoom out
Zoom in
Vorherige Seite
1/21
Nächste Seite
ENGLISH ENGLISH
10
11
InstallationInstallation
Step 3: Setup the Blaster and IR Sensor Step 4: Boot up the Transmitter and Receiver
If necessary, connect the Infrared (IR) blaster (or sensor) Extender cable. Users can point
hand-held remote control of your High Definition AV equipment at the receiver or the
HDTV set to operate the source devices, not exceeding the distance of 66 feet at Line-
of-sight.
IR Blaster Extender cable
Stick IR Blaster to the front
of panel of Source device
1. Plug the IR blaster cable into the IR OUT jack of the transmitter.
2. Please try to manually move the IR blaster in the front of the front panel of your HD de-
vice and then press the key of remote control to search a good position of IR response.
Paste the IR blaster head near the front of IR sensor of your High-Definition audio/video
devices.
3. When the IR blaster cable is connected, it relays infrared command from your remote
control to the device. Users can control their AV devices by pointing their remote con-
trol to the receiver instead of to their AV equipment.
1. Place the two AAA batteries into the remote control.
NOTE:
1. The IR sensor supports 36KHz ~ 56KHz (NEC, RC5, RC6) remote’s signal protocol. There-
fore, it is possible that some devices may not be supported.
2. The IR blaster supports 47KHz remote’ signal protocol.
NOTE:
User can press POWER button of transmitter to turn off both transmitter & receiver simul-
taneously any time.
2. After the power cord is plugged into the electrical outlet, the device will be turned on
automatically.
3. If it is in Standby mode (Both POWER LED of transmitter and receiver are lit in red),
press the POWER button on both transmitter and receiver to turn on the transmitter
and the receiver.
4. If transmitters HDMI out display is on (Transmitter POWER LED is lit in blue) and recei-
ver stay in Standby mode (Receiver POWER LED is lit in red), press the POWER button of
receiver ONLY to wake up and make connection between transmitter and the receiver
for enable display out on receiver side.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Megasat Wireless HD Sender Comfort wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info