Bedienungsanleitung Meliconi Gumbody universal 6 Light (Seite 4 von 7) (Englisch)

494809

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

2. Hold down the selection key for the appliance to be

programmed for 5 seconds.

3. When the key is released, it will start to flash. Enter the

code 0000; the selection key flashes more quickly to

indicate that the remote control is ready for the search.

4. Point the remote control at the appliance. Press and slowly

release the ON/OFF key or PLAY for the VCR and DVD

several times, stopping when the appliance responds

correctly to the command.

5. When the appliance responds correctly, press OK to

confirm. Three flashes indicate that the search operation

has been completed correctly.

+++

0000

ADDITIONAL CHECK

Check that some of the other functions used on your original remote control are working correctly.

If the commands function incorrectly or erratically, you have probably entered a code for a similar remote

control but not the right one. In this case, repeat the search procedure starting from point 2.

To display and make a note of the code memorized by means of the search,

follow the instructions described in the paragraph CURRENT CODE DISPLAY.

N.B. THE LIGHT INDICATOR STOPS FLASHING.

The remote control exits programming mode and the light indicator stops flashing:

• if no keys are pressed for 14 seconds

• if a key other than ON/OFF or PLAY is accidentally pressed

• if the end of the code search list has been reached. In this case, start again from point 2 or

consult our website www.gumbodylight.com.

CURRENT CODE DISPLAY

In addition to what is described above, you can assign the selection keys to appliances other than those

indicated; for example, you can use the SAT key to control the TV. This allows every possible combination

according to your requirements; ust programme the remote control by means of procedure direct code

entry. To find out the appliance code if you have used procedure or , proceed as described in the

paragraph CURRENT CODE DISPLAY.

USING THE REMOTE CONTROL WITH MORE THAN ONE APPLIANCE OF THE SAME TYPE

A C

N.B. this operation cannot be interrupted and the remote control cannot

therefore be used until the end of the 4 series of flashes.

1. Hold down the selection key of the appliance whose code

you want to know for 5 seconds.

2. When the key is released it will start to flash; press and

release the 1-/-- key within 8 seconds.

3. After a few seconds, the light indicator produces 4 series

of flashes, with a pause between each series, correspon-

ding to the current code. Count the number of flashes;

each series of flashes corresponds to one figure in the

code. 10 flashes correspond to 0.

4. Make a note of the code on the adhesive label inside the

battery cover for quick and easy future reprogramming.

........................................................ = 1

............................................ = 3

= 0

.......................... = 6

Code obtained = 1306

To find out the code of your remote control, follow this procedure:

5 SEC.

or or or or or

5 SEC.

or or or or or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meliconi Gumbody universal 6 Light Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info