Bedienungsanleitung Mercedes B-Class Electric Drive 2017 (Seite 279 von 290) (Englisch)

703589

279

Zoom out

Zoom in

Vorherige Seite

1/290

Nächste Seite

Place chocks or other suitable items under

the front and rear of the wheel that is diago-

nally opposite the wheel you wish to change.

Raising the vehicle

WARNING

If you do not position the jack correctly at the

appropriate jacking point of the vehicle, the

jack could tip over with the vehicle raised.

There is a risk of injury.

Only position the jack at the appropriate jack-

ing point of the vehicle. The base of the jack

must be positioned vertically, directly under

the jacking point of the vehicle.

Position a suitable jack correctly on the

intended jacking points. If you fail to position

the jack correctly, the vehicle may be dam-

aged.

The jacking points are recesses in the lower

door sill. They can only be seen from under-

neath. There is one located behind each of the

front wheel arches and in front of the rear

wheel arches.

Position the jack in the jacking points so that

when viewed from the side, the jack is in the

vertical position.

Position a suitable jack only on the jacking

points intended for this purpose.

Never position the jack on the high-voltage

battery. Do not jack up the vehicle on the

high-voltage battery. There is otherwise a risk

of damaging the high-voltage battery.

Also observe the notes in the "Changing a

wheel" section.

Observe the following when raising the vehi-

cle:

To raise the vehicle, only use the vehicle-spe-

cific jack that has been tested and approved

by Mercedes-Benz. If used incorrectly, the

jack could tip over with the vehicle raised.

The jack is designed only to raise and hold the

vehicle for a short time while a wheel is being

changed. It must not be used for performing

maintenance work under the vehicle.

Avoid changing the wheel on uphill and down-

hill slopes.

Before raising the vehicle, secure it from roll-

ing away by applying the parking brake and

inserting wheel chocks. Do not disengage the

parking brake while the vehicle is raised.

The jack must be placed on a firm, flat and

non-slip surface. On a loose surface, a large,

flat, load-bearing underlay must be used. On a

slippery surface, a non-slip underlay must be

used, e.g. rubber mats.

Do not use wooden blocks or similar objects

as a jack underlay. Otherwise, the jack will not

be able to achieve its load-bearing capacity

due to the restricted height.

Make sure that the distance between the

underside of the tires and the ground does not

exceed 1.2 in (3 cm).

Never place your hands and feet under the

raised vehicle.

Do not lie under the vehicle.

Do not start the drive system when the vehicle

is raised.

Never open or close a door or the tailgate

when the vehicle is raised.

Make sure that no persons are present in the

vehicle when the vehicle is raised.

Changing a wheel

277

Wheels and tires

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes B-Class Electric Drive 2017 Seite 279

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mercedes B-Class Electric Drive 2017

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info