Bedienungsanleitung Mercedes C-Class 2017 (Seite 353 von 370) (Englisch)

703595

353

Zoom out

Zoom in

Vorherige Seite

1/370

Nächste Seite

must be positioned vertically, directly under

the jacking point of the vehicle.

Only position the jack at the appropriate

jacking point of the vehicle. Otherwise, you

could damage the vehicle.

Observe the following when raising the vehi-

cle:

To raise the vehicle, only use the vehicle-spe-

cific jack that has been tested and approved

by Mercedes-Benz. If used incorrectly, the

jack could tip over with the vehicle raised.

The jack is designed only to raise and hold the

vehicle for a short time while a wheel is being

changed. It must not be used for performing

maintenance work under the vehicle.

Avoid changing the wheel on uphill and down-

hill slopes.

Before raising the vehicle, secure it from roll-

ing away by applying the parking brake and

inserting wheel chocks. Do not disengage the

parking brake while the vehicle is raised.

The jack must be placed on a firm, flat and

non-slip surface. On a loose surface, a large,

flat, load-bearing underlay must be used. On a

slippery surface, a non-slip underlay must be

used, e.g. rubber mats.

Do not use wooden blocks or similar objects

as a jack underlay. Otherwise, the jack will not

be able to achieve its load-bearing capacity

due to the restricted height.

Make sure that the distance between the

underside of the tires and the ground does not

exceed 1.2 in (3 cm).

Do not place your hands or feet under the

raised vehicle.

Do not lie under the vehicle.

Do not start the engine when the vehicle is

raised.

Do not open or close a door or the trunk lid

when the vehicle is raised.

Make sure that no persons are present in the

vehicle when the vehicle is raised.

Vehicles with alloy wheels and hub caps: the

wheel bolts are covered by a hub cap. Before y

can unscrew the wheel bolts, you must remove

the hub cap. Two different variants can be instal-

led.

Vehicles with plastic hub cap:

To remove: turn the center cover of hub

cap : counter-clockwise and remove.

To install: before installing, ensure that hub

cap : is in the open position. To do this, turn

the center cover counter-clockwise.

Position hub cap : and turn the center cover

clockwise until hub cap : engages physically

and audibly.

Make sure that hub cap : is installed

securely.

Vehicles with aluminum hub cap:

To remove: take socket ; and wheel wrench

= from the vehicle tool kit (

Y page 313).

Position socket ; on hub cap :.

Position lug wrench = on socket ;.

Using lug wrench =, turn hub cap : coun-

ter-clockwise and remove it.

To install: before installing, check hub cap :

and the wheel area for soiling and clean if

necessary.

Put hub cap : in position and turn until it is in

the right position.

Position socket ; on hub cap :.

Attach lug wrench = to socket ; and

tighten hub cap :.

Changing a wheel

351

Wheels and tires

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes C-Class 2017 Seite 353

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mercedes C-Class 2017

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info