Bedienungsanleitung Mercedes C-Class 2018 (Seite 356 von 370) (Englisch)

703610

356

Zoom out

Zoom in

Vorherige Seite

1/370

Nächste Seite

Fold both plates upwards :.

Fold out lower plate ;.

Guide the lugs on the lower plate fully into the

openings in base plate =.

Place chocks or other suitable items under

the front and rear of the wheel that is diago-

nally opposite the wheel you wish to change.

Raising the vehicle

WARNING

If you do not position the jack correctly at the

appropriate jacking point of the vehicle, the

jack could tip over with the vehicle raised.

There is a risk of injury.

Only position the jack at the appropriate jack-

ing point of the vehicle. The base of the jack

must be positioned vertically, directly under

the jacking point of the vehicle.

Only position the jack at the appropriate

jacking point of the vehicle. Otherwise, you

could damage the vehicle.

Observe the following when raising the vehi-

cle:

To raise the vehicle, only use the vehicle-spe-

cific jack that has been tested and approved

by Mercedes-Benz. If used incorrectly, the

jack could tip over with the vehicle raised.

The jack is designed only to raise and hold the

vehicle for a short time while a wheel is being

changed. It must not be used for performing

maintenance work under the vehicle.

Avoid changing the wheel on uphill and down-

hill slopes.

Before raising the vehicle, secure it from roll-

ing away by applying the parking brake and

inserting wheel chocks. Do not disengage the

parking brake while the vehicle is raised.

The jack must be placed on a firm, flat and

non-slip surface. On a loose surface, a large,

flat, load-bearing underlay must be used. On a

slippery surface, a non-slip underlay must be

used, e.g. rubber mats.

Do not use wooden blocks or similar objects

as a jack u

nderlay. Otherwise, the jack will not

be able to achieve its load-bearing capacity

due to the restricted height.

Make sure that the distance between the

underside of the tires and the ground does not

exceed 1.2 in (3 cm).

Do not place your hands or feet under the

raised vehicle.

Do not lie under the vehicle.

Do not start the engine when the vehicle is

raised.

Do not open or close a door or the trunk lid

when the vehicle is raised.

Make sure that no persons are present in the

vehicle when the vehicle is raised.

Vehicles with alloy wheels and hub caps: the

wheel bolts are covered by a hub cap. Before you

can unscrew the wheel bolts, you must remove

the hub cap. Two different variants can be instal-

led.

Vehicles with plastic hub cap:

To remove: turn the center cover of hub

cap : counter-clockwise and remove.

To install: before installing, ensure that hub

cap : is in the open position. To do this, turn

the center cover counter-clockwise.

Position hub cap : and turn the center cover

clockwise until hub cap : engages physically

and audibly.

Make sure that hub cap : is installed

securely.

354

Changing a wheel

Wheels and tires

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes C-Class 2018 Seite 356

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mercedes C-Class 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info