Bedienungsanleitung Mercedes C-Class Sedan 2016 (Seite 122 von 398) (Englisch)

624586

122

Zoom out

Zoom in

Vorherige Seite

1/398

Nächste Seite

To indicate briefly: press the combination

switch briefly to the pressure point in the

direction of arrow ; or ?.

The corresponding turn signal flashes three

times.

To indicate: press the combination switch

beyond the pressure point in the direction of

arrow ; or ?.

To switch on the high-beam headlamps:

turn the light switch to L or Ã.

Press the combination switch beyond the

pressure point in the direction of arrow :.

In the Ã position, the high-beam head-

lamps are only switched on when it is dark and

the engine is running.

The blue K indicator lamp in the instru-

ment cluster lights up when the high-beam

headlamps are switched on.

To switch off the high-beam headlamps:

move the combination switch back to its nor-

mal position.

The blue K indicator lamp in the instru-

ment cluster goes out.

Hazard warning lamps

To switch on the hazard warning lamps:

press button :.

All turn signals flash. If you now switch on a

turn signal using the combination switch, only

the turn signal lamp on the corresponding

side of the vehicle will flash.

To switch off the hazard warning lamps:

press button :.

The hazard warning lamps still operate if the

ignition is switched off.

Cornering light function

The cornering light function improves the illu-

mination of the road over a wide angle in the

direction you are turning, enabling better visi-

bility in tight bends, for example. It can only be

activated when the low-beam headlamps are

switched on.

Active:

if you are driving at speeds below 25 mph

(40 km/h) and switch on the turn signal or

turn the steering wheel

if you are driving at speeds between 25 mph

(40 km/h) and 45 mph (70 km/h) and turn

the steering wheel

The cornering lamp may remain lit for a short

time, but is automatically switched off after no

more than three minutes.

Adaptive Highbeam Assist

General notes

You can use this function to set the headlamps

to change between low beam and high beam

automatically. The system recognizes vehicles

with their lights on, either approaching from the

opposite direction or traveling in front of your

vehicle, and consequently switches the head-

lamps from high beam to low beam.

The system automatically adapts the low-beam

headlamp range depending on the distance to

the other vehicle. Once the system no longer

detects any other vehicles, it reactivates the

high-beam headlamps.

The system's optical sensor is located behind

the windshield near the overhead control panel.

Important safety notes

WARNING

Adaptive Highbeam Assist does not recognize

road users:

who have no lights, e.g. pedestrians

who have poor lighting, e.g. cyclists

whose lighting is blocked, e.g. by a barrier

In very rare cases, Adaptive Highbeam Assist

may fail to recognize other road users that

have lights, or may recognize them too late. In

this or similar situations, the automatic high-

120

Exterior lighting

Lights and windshield wipers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes C-Class Sedan 2016 Seite 122

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info