Bedienungsanleitung Mercedes G-Class 2018 (Seite 280 von 294) (Englisch)

703623

280

Zoom out

Zoom in

Vorherige Seite

1/294

Nächste Seite

Make sure that jack A is at the correct posi-

tion under axle carrier tube ?. The front or

rear axle must sit securely in the recess of

jack A.

Keep pumping until axle carrier tube ? sits

securely in the recess of jack A and the base

of the jack lies evenly on the ground.

Ensure that the jack is located vertically under

the jacking point.

Raise the vehicle by pumping until the tire is

no more than 1.2 in (3 cm) off the ground.

Removing a wheel

Do not place wheel bolts in sand or on a dirty

surface. The bolt and wheel hub threads could

otherwise be damaged when you screw them

in.

When mounting/removing wheels, and for as

long as the wheels are removed, avoid applying

any external force on the brake disks. This could

impair the level of comfort when braking.

Unscrew the wheel bolts.

Remove the wheel.

Mounting a new wheel

WARNING

Oiled or greased wheel bolts/wheel nuts and

damaged wheel bolt/wheel nut/wheel hub

threads can cause wheel bolts/wheel nuts to

come loose. As a result, you could lose a

wheel while driving. There is a risk of an acci-

dent.

Never oil or grease wheel bolts/wheel nuts. In

the event of damage to the threads, contact a

qualified specialist workshop immediately.

Have the damaged wheel bolts/wheel nuts or

hub threads replaced/renewed. Do not con-

tinue driving.

WARNING

If you tighten the wheel bolts or wheel nuts

when the vehicle is raised, the jack could tip

over. There is a risk of injury.

Only tighten the wheel bolts or wheel nuts

when the vehicle is on the ground.

To prevent damage to the paintwork, hold

the wheel securely against the wheel hub

while screwing in the first wheel bolt.

Always pay attention to the instructions and

safety notes in the "Changing a wheel" section

(

Y page 275).

Only use wheel bolts that have been designed

for the wheel and the vehicle. For safety rea-

sons, Mercedes-Benz recommends that you

only use wheel bolts which have been approved

for Mercedes-Benz vehicles and the respective

wheel.

Clean the wheel and wheel hub contact sur-

faces.

Place the new wheel on the wheel hub and

push it on.

Tighten the wheel bolts until they are finger-

tight.

Lowering the vehicle

WARNING

The wheels could work loose if the wheel nuts

and bolts are not tightened to the specified

tightening torque. There is a risk of accident.

Have the tightening torque immediately

checked at a qualified specialist workshop

after a wheel is changed.

Slowly open the pressure release screw on

the jack using the pump lever by approx-

imately one full turn and carefully lower the

vehicle (

Y page 276).

You can put the jack aside.

Tighten the wheel bolts evenly in a crosswise

pattern in the sequence indicated (: to A).

278

Changing a wheel

Wheels and tires

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes G-Class 2018 Seite 280

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mercedes G-Class 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info