Bedienungsanleitung Merida Mountain Bike (Seite 72 von 129) (Englisch)

657613

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Carbon components must not be exposed to excessive

heat. Therefore, never have a carbon component enam-

eled or powder-coated. The temperatures required for

enameling or powder-coating could destroy the com-

ponent. Do not leave carbon ﬁber components near a

source of heat or in your car during hot or sunny weather.

Carbon components have, like all lightweight bike com-

ponents, a limited service life. For this reason, have the

stem and the handlebars checked at regular intervals

(e.g. every three years), even if they have not experi-

enced any undue stress, such as an accident.

When you intend to transport your MERIDA bike in the

boot of your car, be sure to protect the bike or the carbon

frame and components. Blankets, foam tubes or the like

are a suitable padding to protect the sensitive material

from damage. Do not place any bags on your MERIDA

bike lying in your car.

Always park your MERIDA bike carefully and make sure

it does not topple over. Carbon frames and components

may already sustain damage by simply toppling over

and thereby hitting e.g. a sharp edge.

If carbon components on your MERIDA bike

produce any creaking or cracking noises or

show any external sign of damage, such as

gouges, cracks, dents, discolorations etc., do not use

the MERIDA bike any longer. Contact your MERIDA

dealer immediately; he will check the component thor-

oughly.

Do not combine carbon handlebars with bar

ends, unless they are speciﬁcally approved.

Do not shorten carbon handlebars or clamp

the brake levers and shifters more in the middle than

indicated or needed. Risk of breakage!

Make sure all carbon clamping areas are ab-

solutely free of grease and other lubricants!

Grease will penetrate the surface of the car-

bon material, thereby reducing the coefﬁcient of fric-

tion. This will no longer provide reliable clamping with-

in the prescribed torque values. Once greased, carbon

components may never again ensure reliable clamping!

Use a special carbon assembly paste

(a)

instead as of-

fered by various manufacturers.

Most clamps of bike carrier systems are po-

tential sources of damage to large-diame-

ter frame tubes! As a result thereof carbon

frames can fail during use without previous warning.

However, there are special-purpose models which are

suitable, available in the car accessory trade. Inform

yourself there or ask your MERIDA dealer for advice.

Do not clamp a carbon frame or seat post in

the holding jaws of a workstand! The compo-

nents may sustain damage. Mount a sturdy

(aluminum) seat post

(b)

instead and use it to clamp

the frame, or chose a work stand that holds the frame at

three points inside the frame triangle or that clamps the

fork and bottom bracket shell.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Merida Mountain Bike Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Merida Mountain Bike

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info