Bedienungsanleitung Merida Pedelec (Seite 24 von 129) (Englisch)

657614

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Component description MERIDA mountain bike

Stem

Handlebars

Shifter

Brake lever

Headset

Front brake

Rotor

Wheel:

Quick-release/

thru axle

Rim

Tire

Spoke

Hub

Valve

Frame:

Top tube

Seat tube

Down tube

Chainstay

Saddle

Seat post

Seat post clamp

Rear brake

Rotor

Front derailleur

Cassette sprockets

Rear derailleur

Chain

Chainwheel

Crank

Rear stay

Head tube

Rear shock

Suspension fork:

Fork crown

Stanchion tube

III

Lower leg

Drop-out

III

For more information see the chapter “The gears”

and the instructions of the component manufactur-

ers on this MERIDA CD-ROM.

4. Make sure the saddle is not twisted by using the top

tube or the bottom bracket shell as a reference

(a)

If necessary, open the clamping, realign the saddle

and retighten the clamping.

For more information see the chapters “Adjusting

the MERIDA bike to the rider” and “How to use

quick-releases and thru axles” and the instructions

of the component manufacturers on this MERIDA

CD-ROM.

5. Let your MERIDA bike bounce on the ground from

a small height. If there is any rattling, see where it

comes from. Check the bearings and bolted connec-

tions, if necessary. Tighten them slightly, if neces-

sary.

6. Finally, take a good look at the whole MERIDA bike

(b)

to detect any deformations, color changes or

cracks

(c)

. Ride back very carefully by taking the

shortest route possible, even if your MERIDA bike

went through this check without any problems. Do

not accelerate or brake hard and do not ride your

bike out of the saddle. If you are in doubt about the

performance of your MERIDA bike, have yourself

picked up by car, instead of taking any risk.

Back home you need to check your MERIDA bike

thoroughly. Damaged parts must be repaired or re-

placed. Ask your MERIDA dealer for advice.

Deformed components, especially compo-

nents made of aluminum, can break without

previous warning. They must not be repaired,

i.e. straightened, as this will not reduce the imminent

risk of breakage. This applies in particular to the fork,

the handlebars, the stem, the cranks, the seat post and

the pedals. When in doubt, it is for your safety always

the better choice to have these parts replaced. Ask your

MERIDA dealer for advice.

If your MERIDA bike is assembled with car-

bon components

(d)

, it is imperative that you

have it checked by your MERIDA dealer af-

ter an accident or similar incident. Carbon is extreme-

ly strong and durable with very low weight, making it

perfect for the production of high-performance parts.

However, one of the inherent properties of carbon is

that possible overstress may compromise the inner

carbon-ﬁber structure without showing any visible

deformation, as is the case with steel or aluminum. A

damaged component can fail without previous warning.

Risk of an accident!

Make it a rule to check the functioning and in

particular the limit stop of the rear derailleur

after a fall or if your MERIDA bike has toppled

over.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Merida Pedelec Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info