657614
32
Zoom out
Zoom in
Vorherige Seite
1/129
Nächste Seite
32
a
b
c
d
As soon as the axle thread engages with the thread of
the right fork leg, close the axle by turning it clockwise
(a)
. During the first rotations you should be able to rotate
the thru axle nearly without resistance. Tighten the axle
a little.
Close the E-Thru quick-release lever like a usual
quick-release lever
(b)
.
At the beginning you should feel virtually no resistance
and clamping effect. When the lever is at right angle the
resistance you feel should increase significantly and to-
wards the end you should need even more strength to
close the lever.
If the lever cannot be closed completely, re-open it and
turn the axle a little counterclockwise. Try again to close
the quick-release lever
(c)
.
Use the palm of your hand to push it in all the way while
your fingers pull on the fork leg, but not on a spoke or
the rotor.
In its end position the quick-release lever should be
tight so that it can no longer be turned. Make sure the
quick-release lever does not stand out to the front or to
the side. The best closing position is in nearly upright
position in front of the lower leg
(d)
.
Dismounting wheels
If your bike is equipped with a Fox E-Thru 15 mm th-
ru-axle system, open the quick-release lever complete-
ly. Open the thru axle by turning counterclockwise.
Once you have screwed out completely the thru-axle
thread from the thread of the lower leg, you can remove
the thru axle completely.
i
More information are provided at
www.ridefox.com
SR SUNTOUR Q-LOC2 15QL C2 (e.g. SR SUNTOUR
Auron LO-RC)
Mounting wheels
If your bike is equipped with an SR SUNTOUR Q-LOC-
system 15 mm, put the front wheel into the fork and
mount the rotor in the brake caliper, if necessary. Bring the
front wheel into the right position between the drop-outs.
Open the quick-release lever of the SR SUNTOUR thru
axle completely. Turn the counter nut on the thru axle
counterclockwise until the expander releases.
Slide the axle with open quick-release lever and re-
leased expander from the right side through the drop-
out and the hub until the thru axle engages with a clear
“click”. Now turn the quick-release lever forcefully
clockwise until the axle is hand-tight.
Finish by closing the quick-release lever like a usual
quick-release lever. Make sure the quick-release lever
does not stand out to the front or to the side.
32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Merida Pedelec wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info