Bedienungsanleitung Meridian DVP 1080 HD (Seite 30 von 34) (Englisch)

494961

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Tr o u b l e s h o o t i n g

2 6

Processor operation

The LCD is displaying an OVERHEAT WARNING.

The DVP-1080 processor possesses thermal protection circuitry which actively monitors

internal temperature during operation. Excessive heat may cause the processor to

malfunction, and/or, shorten product lifespan.

• Do not mount processor above power amplifiers or other equipment which generate

excessive heat

• Allow a minimum of one rack space, above and below the unit, for proper ventilation

(1RU or 1.75”).

• Insure there is adequate system rack ventilation (preempts failure with additional

installed equipment)

• LEVEL 1 WARNING / HIGH TEMPERATURE

Internal Temperature is exceeding safe operational limits. Steps should be taken to improve

ventilation

• LEVEL 2 WARNING / HIGH TEMPERATURE

Internal Temperature is at critical thermal limits; processor failure may occur. Immediate

steps should be

implemented, to improve ventilation, and return the unit to optimal operational

temperature

• LEVEL 3 WARNING / EXTREME TEMPERATURE

Internal Temperature has exceeded maximum thermal limitations; processor will shut down.

• A LEVEL 3 WARNING will only display for Five (5) Seconds, then the DVP-1080 will shut

down

• DVP-1080 cannot be powered ON by the front panel power button during this condition

• A LEVEL 3 WARNING indication requires the unit first be unplugged to reset

• Normal operation resumes once the DVP-1080 has returned to optimal thermal

temperature

How do I Store a Profile?

A stored PROFILE is merely a “Snap-Shot-In-Time” for all settings which have been selected

from both the SETUP MENU options (LCD), or the USER MENU (OSD) options, within the

DVP1080 processor, and programmed into the processor’s CPU.

System SETUP MENU Option (LCD)

• Enter the SETUP MENU by pressing

Menu on the IR remote for seven seconds

• Select all applicable changes required for the intended PROFILE within the SETUP MENU

• Press

Menu to exit the SETUP MENU

• Then, proceed to…

On-screen USER MENU Options (OSD)

• Press

Menu to view the On-Screen Display (OSD)

• Adjust all applicable changes required for the intended PROFILE

• Under the menu tab INPUT, use

V to highlight PROFILE

• Press the

> to select numeric PROFILE

• Press

Store.

• Press

Menu to exit the On-Screen Display.

When I select 4:3 on the IR remote, the image is not centered

This essentially means the innate 16:9 image from the DVP-1080, when selecting

ANAMORPHIC, is not properly centered on the display device.

• Utilize a DVD ‘Screen Area’ test pattern (DVD Essentials, AVIA, etc.)

• Center, and position the image for a 2.5% over-scan, using the displays sizing and

positioning controls.

• Once the image has been properly centered, sized and positioned (utilizing the display

controls), the 4:3 image will fall-in-to-place and be centered within the 16:9 display

area.

Note: Do not view a 4:3 images for prolonged periods of time on a 16:9 display; image

Burn-In may occur. Image Burn-In is not covered under the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meridian DVP 1080 HD Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info