797763

Mesko MS 7856 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
5
12. Never use the product close to combustibles.
13. Do not let cord hang over edge of counter.
14.Do not immerse the motor unit in water.
15. To provide additional protection, it is advisable to install a residual current device (RCD)
in the electric circuit with a rated residual current not exceeding 30mA. Ask an electrician
for this.
16. Do not insert fingers or any other objects in the housing grille of the device.
17.Do not block the outlet.
18.When done, prior to putting it away, drain water from the device.
19.If the device is not used for a long time, unplug it from the power source.
20.Always use new batteries to replace the drained batteries in the remote control.
21.Do not move the device when the inner tank is filled with water.
22.Do not place any objects on the device.
23.The device can be used only with properly working ventilation.
Before first use
1. It should be remembered that a high level of humidity may favor the development of biological organisms in the environment.
2. Do not get wet the device or wet the area around the device. If moisture appears, reduce the efficiency of the humidifying function.
3. Do not allow absorbent materials such as carpets, curtains, tablecloths to get wet.
4. Never leave water in the tank when the device is not in use.
• WARNING: When the water is not replaced and the tank is not properly cleaned every 3 days, microorganisms that may be present in
the water or in the environment where the device is used or stored may develop in the water tank and be blown out to the surroundings.
This can cause a very serious health risk.
• WARNING: Every three days, empty the water tank and top up with clean water. Before refilling, clean the tank with fresh tap water or
using detergents. Remove any scale, deposits or film that has formed on the sides of the tank and on the interior surfaces. After
washing, wipe all surfaces dry.
5. When the device is used for the first time the device’s motor may produce an odor which will dissipate within a week of use. There is
no required your action in this case.
PRODUCT DESCRIPTION Bladeless air cooler Ms7856
1. Handle 2. Air outlet
3. Handle to manual up / down air flow direction control 4. Front housing
5. Water level gauge 6. Back housing
7. Back cover with net 8. Evaporation filter
9. Water tank 10. Remote control
11. Ice boxes 12. Control panel
13. Water tank lock 14. Pump latch
15. Pump 16. Cover’s recess
17. Filter latches
Remote control & Control panel – picture B
A – power button B – mode button
C – fan speed button D – timer button
E – timer button F - wet cooling button
OPERATION
A noticeable reduction in the temperature of the outlet air occurs after putting into the water tank (9) the plastic containers (11) included
to the product. The plastic containers should be previously frozen in the freezer for few hours. It is recommended to fill the plastic
container (11) with cold tap water and do not exceed MAX level marked on the plastic container. The content of plastic container is
prohibited to edible. Keep away from children.
1. Place the device on a dry, flat surface. If the surface is not flat, the device can start vibrate and get abnormal noise.
2. Rotate to flat position the water tank lock (13) as shown at pictures C1 and C2. Then, pull out a little the water tank (9) from the back
of the device. Use the jug to pour clear, cold water, be careful not to exceed the maximum level marked at water level gauge (5) at front
of device. You can pour water w/o pulling out the water tank completely. During filling and cleaning, disconnect the device from the
mains.
3. To remove water tank completely look at picture C3-C6. At first remove the pump (15) by releasing one pump latch (14) and pull out
the water tank (8). Do not pull out the pump, let it stay connected to main housing. When you place the water tank (9) back take
attention to not squeeze the water pipes connected to the pump.
After water pouring, turn the water tank lock (13) to horizontal position. Do not tilt the device after pouring the water to water tank. Do not
remove water tank while the device is plug in power supply.
4. Connect the plug to power supply. Now can be used control panel (12) or remote control (10) to operate the device (figure B). Turn on
the device by pressing the power button (A). Press the button (A) again to switch off the device.
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Mesko MS 7856 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info