10 11
Please read the instructions thoroughly before using the pump! Otherwise you may no
This appliance is not suitable for use b
capabilities or lacking experience and/or knowledge
for their safe
Children should be supervised in order to make sure tha
Construction
These modern, powerful pumps are equipped with a single-phase alterna
with capacitor). The mot
ov
Please refer to the type plate for technical specifications or the table on page 2 + 3.
Use
These pumps are designed for t
wat
Area of application: garden ponds, fishponds, outdoor and patio fountains! (see fig. 1 + 2)
- Attention! Use in garden ponds and t
performed in complianc
- Before performing any work on the pump, t
plug. Do not operate the pump if people are in the water! (disconnect the pump from the power
source)
Area of application: swimming pond or swimming pool (if people are in the water)! (see fig. 3 + 4)
Pump suitable for installation and oper
Part 737, if the erection requir
and operating instructions) ar
Installation of these pumps a
standards: DIN EN 13451 P
Attention! Here operation of the pump is permitted only if the pump is permanently installed outside
of the water at least 2 m or more awa
The following measur(see fig. 3)
- Build a shaft with pedestal for the pump, at least 2 m awa
- Protect the shaft with a cov
- T
- Attach the pump to the pedestal with scr
- Install a “M” metal socke
of the swimming pond/swimming pool sy
- Please consult a licensed electrician. Also re
Safety measures
- Before use
- Mains voltage and kind of current ha
- The pump may only be connected to a pr
current device (RCD, 30 mA).
- The connection box should be located in a w
edge of the water (see fig. 1 + 2).
- Alwa
- Important! If the mains lead or the motor housing are damaged
It cannot be repaired since the lead is permanently encapsulat
- Do nev
Start-up (see fig. 1 - 4)
Important! Do not let the pump run „dry“. This could cause damag
- Immerse the pump completely in y
- A minimum wat
- The maximum depth for submerged operation of the
2 m
- The wat
- The pump must be prot
- The pump is switched on b
- T
firm and horizontal position (on a st
- A range of accessories may be fitted onto the thr
GB
- For intakArt.-No. 168 / 009050, 1
from our line of accessories (catalog).
- The pressure duct can be mounted on t
T
- Suitable fountain jets can be found in our r(catalog) .
“Non submersible use” (see fig. 3 + 4)
The pump can be used in a nonsubmerged type application.
- Position t
the pump (not self-priming).
- Connect suction hose (S) and pressure hose (D) to the pump. C
- Suction hose and pump must be filled with wat
- TIP! T
Art.-N cover
Overload protection
In case the pump is becoming overhe
The pump must cool down.
The pump will not start automatically without the necessary controlling when it is cool.
Check the following opera
- Is there a sufficient wa
- Has the filter become clogged?
- Has dirt entered the pump housing (Follo
- Hav
- Has the pump cooled down?
As soon as you ha
socket and putting it in again after a short time (1 min.)
Dismantling (see fig. 5)
1. Disconnect pump from mains!
2.
3.
4.
housing (10).
5. Note! In c
Messner decalcifier for pumps Art.-No. 168 / 0091.
Assembly (see fig. 5)
1.
2.
the two holes fit onto the pins on the motor housing (10).
3.
4.
5.
4 screws (18) .
Maintenance
In order to prolong the service life of your pump significantly and t
recommended to carry out maintenance and cleanup regularly
This can be done by evSee „Dismantling/Assembly“
Servicing inter
- In the beginning check proper performance of your pump ev
- Since servicin
periodic ser
Should you dedamaged or worn parts , replace them. See „Spare parts“
Important! When used in calcareous water
tube in the motor housing (1
Pump care in wintertime
Protect your pump from freezing-up!
T
Clean the pump completel
During the winter months st
Store the tank in a fr
