Bedienungsanleitung Messner system-Tec 4000 (Seite 8 von 27) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

609981

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

12 13

Dismantling / Assembly (see ﬁg. 2 - 5)

1. Follow the safety measures. Disconnect the pump!

2. Pull the ﬁlter cover (1) off of the pump.

3. Twist the intake lid (6) clockwise and pull it out of the pump (8).

4. The front bearing support (4.5) and an axial bearing washer (4.4) are situated in the inlet lid (6) or on

the axle (4.3) respectively.

5. Pull the rotor (4) out of the pump (8).

6. The complete rotor (4) can be rotated on the shaft (4.3).

7. The ﬂywheel (4.2) and the magnet (4.1) can also be rotated against one another at a certain angle.

8. Thoroughly pull the axle (4.3) out of the pump (8).

9. Push the rear bearing support (4.5) including the axial bearing washer (4.4) out of the pump; you may

ﬁnd a pen to be helpful to accomplish this.

10. Insert this pen in the small bore at the pump‘s rear side (8) and use it in order to push the rear bearing

support (4.5) including the axial bearing washer (4.4) out of the pump.

11. Clean all components - please use clear water only - so that they allow to be easily moved. Do not use

sharp-edged objects.

12. Proceed as follows in order to reassemble the pump:

12.1. Put the rear bearing support (4.5) including the axial bearing washer (4.4) onto the axle (4.3) and

insert it in the pump (8).

12.2. Put the rotor (4) onto the axle (4.3).

12.3. Put the front bearing support (4.5) including the axial bearing washer (4.4) onto the axle (4.3).

12.4. Twist the intake lid (6), insert it into the pump (8) and turn it counter-clockwise up to its stop.

12.5. Fit the ﬁlter cover (1) back on the pump.

To ensure proper functioning, repeat the above procedure frequently, depending on clogging and working

time.

Maintenance

In order to prolong the service life of your pump and to keep it in good operating condition, it is

recommended to carry out maintenance and cleanup regularly. This can be done by everyone, quickly and

easily. See „Dismantling/Assembly“

Servicing intervals

- In the beginning check performance of your pump every day. If necessary, clean the ﬁlters.

- Since servicing intervals (complete cleanup) will vary depending on pond pollution, repeat the periodic

service to your pump in accordance with the requirements given.

Should you determine that there are damaged or worn parts, do replace them. See „Spare parts“.

Winter / Pump care

Protect your pump from freezing-in!

Take the pump out of your pond in autumn.

Clean the pump completely following the outlined instructions.

During the winter months store the pump in a frost-resistant room.

Spare parts

For ordering spare parts, please indicate the pump type, the designation and the Art.-No. as per table below

(see also ﬁg. 4 - 6).

Item Designation Pump Type Art-No.

1 Filter cover system-Tec 1000, system-Tec 2000 104 / 004473

system-Tec 3000, system-Tec 4000 104 / 004476

2 Cover plate system-Tec 1000, system-Tec 2000 104 / 004475

system-Tec 3000, system-Tec 4000 104 / 004478

3 Base system-Tec 1000, system-Tec 2000 104 / 004477

system-Tec 3000, system-Tec 4000 104 / 004474

4 Rotor system-Tec 1000 168 / 009145

system-Tec 2000 168 / 009117

system-Tec 3000, system-Tec 4000 168 / 009172

6 Lid system-Tec 1000, system-Tec 2000 168 / 009146

system-Tec 3000 168 / 009110

system-Tec 4000 168 / 009174

7 Triple distributor system-Tec 1000, system-Tec 2000 164 / 004485

system-Tec 3000, system-Tec 4000

Socket G ½˝ system-Tec 1000, system-Tec 2000 104 / 004488

Socket G ¾˝ system-Tec 3000, system-Tec 4000 104 / 004489

Guarantee conditions

This pump comes with a 24-month guarantee that is effective from the date of delivery. The invoice will be

the proof of the date. In case of damages due to defects in material or manufacturing, we shall either do a

free repair during the guarantee period or replace the damaged part, the choice being ours’.

Damages that occur due to installation and operating errors, lime deposits, insufﬁcient care, frost action,

normal wear and tear or improper repair attempts will not come under this guarantee. The guarantee will

not be valid in case of modiﬁcations to the pump, e.g. cutting off the line connection or the line cord. We

will not accept responsibility for consequential damages resulting from breakdown of the pump or improper

operation.

When making use of the guarantee, please send us the pump, along with the corresponding invoice, free of

charge via the specialist dealer who sold you the pump.

Waste disposal

Waste disposal of electronic devices by the user in private households of the EU

It is not allowed to dispose the product along with the regular waste disposal, instead it has to be collected

separately. It is your responsibility to dispose and recycle the device in a proper place and protect the

environment through this. More information, where to dispose your devices can be obtained at the local

departments.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Messner system-Tec 4000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info