Bedienungsanleitung Messner Titan-Tec 13000 (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

609993

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Please read the instructions thoroughly before using the pump! Otherwise you may not use it!

This appliance is not suitable for use by persons (including children) with limited physical, sensory or mental

capabilities or lacking experience and/or knowledge, except if they are supervised by a person responsible

for their safety or have been instructed in the use of the appliance.

Children should be supervised in order to make sure that they do not play with the appliance.

Construction

These modern, powerful pumps are equipped with a single-phase alternating-current motor (canned motor

with capacitor). The motor is waterproof encapsulated in synthetic resin (IP68) and provided with an

overload protection.

Technische gegevens vindt u op het typeplaatje resp. in de tabel op pag. 1.

Use

These pumps are designed to displace water for operating ﬁ lter systems, as well as for water aeration and

circulation in or on aquariums, ﬁ sh farms or ﬁ sh keeping pools with sea water or salt water.

Safety measures

- Attention! Use in aquariums, ﬁ sh farm pools and their protected areas is only permitted if the installation

complies with the valid regulations. Contact a qualiﬁ ed electrician.

- Unplug the mains plug before performing any task on pump, pool or aquarium.

Do not operate the pump if people are in the water! (Disconnect the pump from the mains supply)

- Before use: Check whether mains lead and plug are intact.

- Mains voltage and kind of current have to conform to the information on the type plate.

- The pump may only be connected to a proper earthing-contact type socket through a residual

current device (RCD, 30 mA).

- Install the connection power outlet in an area that is protected from water (see Fig. 1 - 3).

- Install a portion of the cable with a downward bend, so that water cannot ﬂ ow along the cable to the plug

or power outlet (X). If water should nonetheless get to the plug or power outlet, avoid any contact! In this

case interrupt the power supply to the power outlet before you unplug the mains cable.

- The pump should only be set up inside of the home!

- Do not operate the pump if the mains connection cable, the plug or the housing are damaged.

- Always keep the plug dry.

- Important! If the mains lead or the motor housing are damaged, the pump cannot be used anymore.

- It cannot be repaired since the lead is permanently encapsulated in the motor housing. In this case the

pump must be scrapped / disposed of.

- Do never hang up or transport the pump by the mains lead.

- Strictly comply with these safety measures, particularly if children are in the vicinity.

Start-up (see ﬁ g. 1 - 4)

Important! Do not let the pump run „dry“. This could cause damages to the appliance.

- Completely immerse the pump in water.

- A minimum water depth of 25 cm is required for underwater operation to avoid the pump taking in air.

- The maximum depth for submerged operation of the

1 m pump is 1 m!

- The water temperature may not exceed 35°C.

- The pump must be protected from frost.

- The pump is switched on by putting the plug in the socket.

- A range of accessories may be ﬁ tted onto the threaded connections of the pump.

- As intake protection select a pre-ﬁ lter, item no. 68 / 009137 to 168 / 009140 from our accessory

program (catalogue).

- The pressure duct can be mounted on top or on the side depending on the particulary implementation!

To do this loosen the screws (20) and turn the entire pump (10) to the desired position.

“Non submersible use” (see ﬁ g. 3)

The pump can be used in a nonsubmerged type application.

- Set up the pump below the water surface, next to the pond or aquarium, so that the water can ﬂ ow to the

pump (not self-priming).

- Connect suction hose (S) and pressure hose (D) to the pump. Connection should be watertight.

- Suction hose and pump must be ﬁ lled with water before switching-on.

- TIP! To prevent the pump becoming clogged, provide the suction hose with a pre ﬁ lter

Art.-No. 168 / 009137 to 168 / 009140 covered in our range of accessories.

Overload protection

In case the pump is becoming overheated the built-in thermal overload trip switches it off.

The pump must cool down.

The pump will not start automatically without the necessary controlling when it is cool.

Check the following operating conditions:

- Is there a sufﬁ cient water supply?

- Has the ﬁ lter become clogged?

- Has dirt entered the pump housing (Follow the cleaning instructions below)?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Messner Titan-Tec 13000 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info