Bedienungsanleitung Messner Versailles (Seite 8 von 17) (Deutsch, Englisch, Französisch)

609971

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

12 13

Drive/Distributor

sectional view

Distributor cover

Distribution,

Fan Jets

Center connection,

Fountain Jet

Flap and spring

Sectional view without gear

Distribution,

Ring Jets

Bore Ø 6 mm

towards

pump

Distribution,

Bell Jets

Drive/Distributor

topview

Repair work

Pull out mains plug of the pump and the lighting before all repair and maintenance work.

Opening of the waterworks

Unscrew the bell jets and turn the waterworks upside down (jets downwards).

In order to prevent the jets from being scratched, it is advisable to use a soft underground (foam material).

Turn the 6 screws with hexagonal recessed holes on the outside and the hexagon cap screw in the middle

out of the base plate of the waterworks.

Thereby it is possible to do all repair work.

Failure of a water pattern or permanent running of one water pattern:

Phase 1: Bell jets and fan jets

Phase 2: Fan jets and ring jets

Phase 3: Ring jets and fountain jet

Phase 4: Fountain jet and bell jets

Mechanical load and natural wear

and tear may result in a failure of

the component parts of the drive/

distributor.

Please proceed as follows:

1. Open the waterworks

(as described before).

2. Loosen the eight screws on the

distributor cover of the drive and

remove the cover.

3. From the drawing you can learn

which distribution or which center

connection runs to the jet failed.

Draw this element out of its

conductor and check whether:

a) the stainless steel spring,

ﬂ ap or holder are broken

b) the ﬂ ap closes automatically

c) the closed ﬂ ap ﬁ ts snugly;

do compare with the other ﬂ aps.

4. If there is a damage, we recommend

to replace the complete set,

3 x distribution and 1 x center

connection.

Lighting

In case the lighting has failed, maybe the halogen incandescent lamp in the ﬂ oodlight has exceeded its

service life.

Loosen the two tapping screws beside the defective ﬂ oodlight and pull it out of the appliance together with

the holding ring. By bending up the three hooks, separate the ﬂ oodlight from the holding ring.

Changing of the lamp

Attention! As a replacement, one may use (nearly) all commercial cool-beam, reflectable lamps,

max. 50 watts.

1. Pull out mains plug and secure against reclosing.

2. Hold tight the ﬂ oodlight casing and unscrew the ﬂ oodlight ring anticlockwise.

3. Remove the ﬂ oodlight glass.

4. Remove the lamp from the casing and remove the ceramic socket.

5. Before re-assembling the ﬂ oodlight, please clean the glass and the sealing ring.

Do avoid using scouring liquids or any sharp instruments.

The sealing ring is ﬁ tted to the casing and should not be removed.

6. Replace the lamp, put it again in the socket and re-insert it into the casing.

7. Place the glass on the sealing ring which is provided on the casing, put back the ﬂ oodlight ring and screw

it clockwise.

For re-assembling the complete ﬂ oodlight on the appliance, clip the holding ring again to the ﬂ oodlight,

re-insert both pieces into the “Versailles” and tighten with the 2 tapping screws.

Taking care of your waterworks in winter

Protect the waterworks against frost.

Take the appliance out of the water in autumn and store it in a frost-proof room during the winter months.

Guarantee conditions

This Water Display «Versailles mini» comes with a 24-month guarantee (ﬂ oodlight lamp excluded) that

is effective from the date of delivery. The invoice will be the proof of the date. In case of damages due to

defects in material or manufacturing, we shall either do a free repair during the guarantee period or replace

the damaged part, the choice being ours’.

Damages that occur due to installation and operating errors, lime deposits, insufﬁ cient care, frost action,

normal wear and tear or improper repair attempts will not come under this guarantee. The guarantee will not

be valid in case of modiﬁ cations to the apparat, e.g. cutting off the line connection or the line cord. We will

not accept responsibility for consequential damages resulting from breakdown of the apparat or improper

operation.

When making use of the guarantee, please send us the apparat, along with the corresponding invoice, free

of charge via the specialist dealer who sold you the apparat.

Floodlight ring

Glass

Lamp

Socket

Sealing ring

Floodlight casing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Messner Versailles Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Messner Versailles

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info