Bedienungsanleitung Mestic SPA-3000 (Seite 22 von 48) (Deutsch, Englisch, Französisch)

782544

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

7. Error code list

If the device does not work or works insuf ciently:

Check if an error code is visible in the display, refer to the error code table for a solution. If no error code is visible in the display, go through the error table for a

possible solution.

Error codes

error code Cause Solution

E1 room temperature sensor fault Contact the dealer

E2 system temperature sensor fault

E3 Insuf cient re gerant

E4 Fan failure

E5 condensation pump malfunction

8. Failure guide

Failure guide

Problem Cause Solution

The device does not turn on No power Turn power on

damaged electrical outlet Turn off the power and check / repair the power

outlet

Unknown reason Contact the dealer

Little air displacement or limited cooling effect The lowest ventilation setting is selected Select the medium or high ventilation speed modus

The air  lter is dirty Check and clean the  lter

The air supply or exhaust of the indoor unit is

blocked

Check that the unit is not blocked and remove the

obstruction

The air supply or exhaust from the outdoor unit is

blocked

Check that the unit is not blocked and remove the

obstruction

The ambient temperature is too low or high The ambient temperature must be between 16 and

40 ° C

Insuf cient voltage from the power supply Consult an installer or use a different power con-

nection

Air displacement only but no cooling effect The device runs in ventilation mode Select the cooling mode (A / C)

The cooling mode has just turned off automatically Wait about 3-5 minutes until the thermostat swit-

ches on again

Abnormal sounds or vibrations The mounting brackets are not properly installed on

the vehicle, or the device mounting screws are not

suf ciently tightened

Check that the mounting bracket is tight and tighten

the device mounting screws

Water is leaking from the indoor unit The rubber stopper on the bottom of the indoor unit

is missing, or is not pressed enough

Check or replace the plug

The device is at an angle The device must be mounted horizontally (maxi-

mum angle <3 °)

The appliance emits a related odor There is a serious problem Switch off the device immediately and contact the

dealer

9. Maintenance

To clean

Caution: Unplug the power cord before cleaning the product.

For cleaning the outside:

Wipe the outside with a damp cloth. Then dry the device thoroughly with a dry cloth. Do not allow water or detergent to enter the machine. Do not clean the air

conditioner with an aggressive cleaning agent and / or petrol.

Clean  lter:

It is important to regularly remove the dust from the  lter. Remove the  lter as shown in the picture below. Clean the  lter with tap water and / or a vacuum cleaner

to remove any dirt from the  lter. Make sure the  lter has dried before putting it back in the air conditioner. Do not use water hotter than 40 ° C for cleaning and do

not expose the  lter to the sun.

pull the handle

Filter

pull

Lift

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mestic SPA-3000 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info