451399
13
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
5.3 Switch/Motor Protection Relay
The following only applies for machines equipped with motor brake and/or no-voltage release feature.
The magnetic switch is not operational when machine is disconnected from power. It disengages in the event of
a power failure (no-voltage release). After power is restored motor has to be started again. A light hum of the relay,
when motor is switched off, is normal and does not represent a fault.
The built-in motor protection relay switches the motor off in case it becomes too hot. If this has happend let motor
cool down for 10 minutes before starting again.
On 3-phase machines the motor protection relay also cuts out if one of the phases should fail. If relay cuts out
repeatingly, check fuses of all three phases.
6 Operation
6.1 Selection of Saw Blade Speed
This band saw can be set to four different cutting speeds for best possible cutting results in different materials.
Depending on type of blade used and material to be cut, the following general recommendations are given:
a) 967/1160 m/min - all species of wood
b) 375/450 m/min - hardwood, certain plastics and NF-metals
c) 176/211 m/min - NF-metals and most plastics
d) 68/82 m/min - low-carbon steel, gas aerated concrete blocks
It is recommended to make trial cuts in scrap material at different settings to find the best cutting speed.
6.2 Change of Saw Blade Speed
To change cutting speed, the v-belts must be changed on the pulleys according to the instructions given on the table
inside the lower wheel housing door.
For easy change of belts a quick-action tensioning device is provided, activated by the cranked handwheel (20)
at lower right of the wheel housing.
6.3 Changing/Setting of Saw Blade
This band saw is factory-equipped with a general purpose woodcutting blade, size 3380x15x0.5 mm, tooth spacing
6 mm.
To change blade, remove rip fence carrier extrusion (86) from saw table. Then slacken blade tension by turning
blade tensioner handwheel (16) counter-clockwise, open both doors and swing saw blade guard out of the way.
Remove blade from machine.
Fit new blade and tension lightly. Blade must run in centre of band saw wheels or else it will jump off. To check
tracking turn upper wheel by hand. If necessary, adjust tilt of upper band saw wheel with starknob setting screw
(28) at rear of upper wheel housing. If a blade of different width is fitted. the thrust bearings of the upper and lower
blade guide must be adjusted. Set thrust bearings against blade so that its teeth are just running clear of the guide
bearings/pilot pins. Fully tension blade.
6.4 Guiding of Saw Blade
For a clean and straight cut sufficient lateral support of the blade is necessary. This support is provided by the
3-roller guide at the blade guard assembly. Keep the guide bearing set closely against the blade, with only minimal
play of the blade, for best performance.
The pilot pins (25) of the lower blade guide are subject to wear. Regularly check blade for play and adjust pins to
take the play out.
To adjust, loosen threaded pins at rear of pilot pin guide with Allan key 3 mm, provided with machine, and set pilot
pins against blade, touching it lightly.
13
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

metabo-bas-450

Suche zurücksetzen

  • Sehr geehrte Damen und Herren,
    ich möchte gerne eine Bandschleifvorrichtung, Best.Nr. 090 900575 2, kaufen.
    Ich besitze eine BAS 450, leider kann ich diese Schleifvorrichtung nirgends finden.
    Hoffentlich können sie mir helfen.
    Vielen Dank im Voraus.
    Liebe Grüße
    Reinhard Frankerl Eingereicht am 31-3-2023 13:20

    Antworten Frage melden
  • Suche Untertisch Bandführung für BAS450 ser.Nr. 2006.682
    198 Eingereicht am 9-5-2022 18:07

    Antworten Frage melden
  • Hello,
    I have been searching for quite a while now and I am unable to finde the differences between the models 450 WN, WNB, DN and DNB. Does someone know what the differences are between these models?
    Thanks a lot.
    Cheers Eingereicht am 12-10-2018 15:25

    Antworten Frage melden
  • Wie ist die Artikelnummer für die Keilriemen der Bandsäge BAS 45 DB
    Eingereicht am 7-9-2018 11:36

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo BAS 450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info