ENGLISHen
10
– Keep in mind that the tool starts up
automa
reached! – En
power before serv
– Ensure that when switchin
servicing) no
the tool.
4.5 Hazard generated by insuffic
personal protection gear!
– Wear hearing protection.
– Wear protective goggles.
– Wear a breathin
generati
vapours are generated.
– Wear suitable work clothes.
– W
4.6 Hazard generated by tool defects!
– Keep tool and accessories in go
Observe the maintenance instructions.
– Prior to each use check the tool for any eventual
damage: Before cng to use the tool,
safety devices, protective devices or lightly
damaged parts must be carefully inspected
correct and proper operation. A damaged
device must only be reused after it has been
correctly repaired.
– Check to see that all moving parts work pro
and do not jam. All parts must be
installed and fulfil all conditions neces
ensure perfect opera
– Damaged protection devices or parts m
repaired or r
4.7 Additional Safety
– Please also observe the special safety
instructions
– Observe any particular health and safety or
accident prevention
use of compressors and com
– Observe the legal provisions for the operation of
systems requir
– Keep in mind th
other consumable
surrounding area
environment during operation and storage of the
tool.
– Consider environmental con
4.8 Symbols on the machine (depends
on model)
Read the operating instructio
Warning of pers
parts.
Wear eye goggles
Wear ear protectors.
Warning of automatic startup.
Danger - electrical voltage.
Guaranteed sound power level.
4.9 Safety devices
Safety valve
The spring-loaded valve (4) reacts if the permitted
maximum pressure is exceeded.
See page 2.
1c
2 pressure vess
3c
4 safety valve
5 connection fo
coupling), regulated com
6 manometer control pressure
7p
8 manomet
9O
10 motor protection switch *
11 air filter / air filter housing
12 oil sealing plug
13 oil insp
14 oil discharge plug *
15 transport handle *
* depends on model / equipment
6.1 Assembly (depending on model)
1. Mount the tyres as shown (see fig. A, page 3).
2. Mount the rubber feet as
page 3).
3. Screw the enclosed air filter (11) onto the air
inlet (see fig. C, page 3).
6.2 Check condensate outlet
Ensure that the condensate outlet (3) is closed.
6.3 Fill oil
(Basic 250-24 W, Basic 250
Oil quality and quantity (approx. deta
chapter 12. Technical
1. Unscrew the oil plug (12) .
2. Fill oil until th
glass (13) or th
3. Screw back in (12) the oil plug.
6.4 Installat
The positioning site of the
following requiremen
– Dry, prote
– Stable, horizontal and even surface
Danger!
Wrong position
– Secure the device against rolling away
and slipping.
– Safety installations and operating elemen
have to be easily
– (Basic 250-24 W, Basic 250-50 W) Do not place
the device on its side. Oil migh
6.5 Transport
– (Basic 250-24 W, Basic 250-50 W) Do not place
the device on its side. Oil migh
– Do not pull the device from the hose or mains
cable. Transport the device at the transport
handle (15).
7.1 Power-supply connection
Danger! High voltage.
Operate the device in dry surroun
Operate the device only
meeting the following requirem
installed according
tested; fucording to the technical
data.
Position power supply
interfere with the work and is not damaged.
Check every time if the device is switched off,
prior to plugging the mains plug into the socket
outlet.
Protect power supply cable from
liquids and sharp
Use only extension cables
cross-section
Use extension cables for outdoor areas. When
working outdoors, only us
marked extension cable approved for th
purpose.
Do not switch off the compressor by pull
mains plug, but use the ON/OFF switch.
Always install an RCD with a maximum trip
current of 30 m
7.2 Generate compressed air
1. Switch on the device usi
(9) and wait, until th
pressure has been reached (com
switches off). The boiler pressure is s
the boiler pressure ma
Set the control pressure at the press
(7) . The current control pressu
control pressur
Attention!
The set control pressure mu
maximum operating pressure of the connected
compressed air
2. Connect the compressed air hose at
compressed air inlet (5) .
3. Connect the compressed air tool. Now you
can work with the comp
4. Switch off the tool if you don't want to continue
working immeAfterwards pull the
mains plug.
5. Drain the condensed water of the pressure
vessel at the condensate outlet (3) on a daily
basis.
Danger!
Prior to all servicing:
Switch machine off. Disconnect the mains plug.
Wait until the device has stopped. Ensure that
there is no more pressure on the device and all
used compressed air
Leave the device and all used com
tools and accesso
After to all servicing:
Put back into operation and check all safety
installati there are no tools or
similar at or in the device.
Repair and maintenance work ot
described in this section should only be carried
out by qualified
8.1 Important information
Maintenance and test have to be planned and
carried out in accordance with the legal
provisions in the setup and mode of
operation of the device
Regulatory authorities may ask to view respective
documentation.
8.2 Regul
Prior to every start
– Check c
replace, if necessary.
– Check that all screw fittings are seated securely,
and tighten if necessary.
– Check connection cab
necessary, have it replaced by a qualified
electri
Daily
– Drain the condensed water of the pressure
vessel at the condensate outle
Every 50 hours of operation
– Clean air filter (11) (see fig. D, page 3).
– (Basic 250-24 W, Basic 250-50 W) Check the
oil leveor at the inspection
glass (13), if necessary refill oil.
Every 250 hours of operation
– Clean air filter (11) or replace (see fig. D, page
3).
Every 500 hours of operation
– (Basic 250-24 W, Basic 250-50 W) Completely
drain the oil at the oil outlet plug (14) and
replace. (See chapter 6.)
5. Overview
6. Commissioni
7. Operation
8. Care And Maintenance
