Bedienungsanleitung Metabo BASIC 330 SILENT (Seite 12 von 50) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch)

658511

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

ENGLISH

4.2 Mains connection

Danger! High voltage

Operate device in dry environ-

ment only.

Operate device only on a power

source complying with the following

requirements:

− outlets properly installed, earthed

and tested;

− fuse protection in accordance

with the technical specifications.

Position power cable so it does not

interfere with the work and is not

damaged.

Always check to see that the device is

switched OFF before plugging in.

Protect power cable from heat,

aggressive liquids and sharp edges.

Use only extension cables with suffi-

cient lead cross section (see "Techni-

cal Specifications").

Do not stop the compressor by

unplugging, but switch OFF using the

switch.

Unplug after use.

4.3 Generating compressed

air

1. Start device (33) and wait until the

max. tank pressure is reached

(compressor shuts off).

The tank pressure is indicated by

the tank pressure gauge (37).

2. Adjust pressure regulator (34) to

required working pressure. The cur-

rent working pressure is indicated by

the regulated pressure gauge (36).

Caution!

The regulated pressure must

not be set higher than the max. work-

ing pressure of the connected air

tools!

3. Connect air hose to compressed air

outlet (35).

4. Connect air tool.

You are now ready to work with the

air tool.

5. Switch the compressor OFF, if you

do not continue working immediately

afterwards. Unplug after switching

OFF.

Danger!

Prior to all servicing:

− Switch Off.

− Unplug.

− Wait until the device has come to

a complete stop.

− Ensure the device and all air tools

and accessories connected to it

are relieved from pressure.

− Let the device and all air tools

and accessories used cool off.

After all servicing:

− Check to see that all safety

devices are operational.

− Make sure that no tools or other

parts remain on or in the device.

Repair and maintenance work other

than described in this section must

be carried out by qualified specialists

only.

5.1 Periodic maintenance

Prior to each use

• Check air hoses for damage,

replace if necessary.

• Check all screwed connections for

tightness, tighten if necessary.

• Check power supply cable for dam-

age, if necessary have replaced by

a qualified electrician.

Every 50 operating hours

• Check air filter element (38) of com-

pressor pump, clean if necessary.

To do so, loosen screws of the

upper sound insulation hood and

remove hood.

• Check oil level of pump with oil dip

stick (39), top up if necessary.

• Drain condensate from pressure

vessel (40).

• Clean air filter element (41) of filter/

regulator unit.

• Drain condensate from filter/regula-

tor unit (42).

33 34

5. Care and maintenance

MAX

MIN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo BASIC 330 SILENT Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info