Bedienungsanleitung Metabo BE Partner Edition (Seite 12 von 64) (Alle Sprachen)

658455

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISHen

Clamping the tool: Insert tool -2- as far as possible

and, using the chuck key, evenly secure in all 3

bores -3.

7.7 Unscrewing chuck (when screwing with-

out chuck or when using attachments)

See illustrations C, D on the second last page.

Note for illus. C, D: Release by tapping lightly with a

rubber hammer, as shown, and unscrew.

Note:

If a bit clamping bush (order no. 6.31281) is

attached, the screwdriver bit inserted in the

hexagon socket of the spindle is held in place.

Cleaning the keyless chuck:

After prolonged use hold the chuck vertically, with

the opening facing down, and fully open and close it

several times. The dust collected falls from the

opening. Regular use of cleaning spray on the jaws

and jaw openings is recommended.

Electronic signal display (6) (BEV 1300-2)

Rapid flashing - restart protection

When power is restored after a power failure, the

machine - which is still switched on - will not start by

itself for safety reasons. Switch machine on and off

again.

Slow flashing - carbon brushes worn

The carbon brushes are almost completely worn.

If the brushes are completely worn, the machine

switches off automatically. Have the brushes

replaced by an authorised service centre.

Permanently lit - overload

If the machine is subject to continuous overloading

for longer periods, the power input to the machine is

limited. This prevents additional unauthorised

heating of the motor. Run the machine in idling until

it cools down and the electronic signal display

switches off.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

For a complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

Explanatory notes on the information on page 3.

Changes due to technological progress reserved.

=Rated input

=Power output

* =No-load speed

* =Load speed

ø max =Max. drill diameter

b =Chuck capacity

G =Drill spindle thread

H =Drill spindle with hexagon socket

m=Weight

D =Collar diameter

Measured values determined in conformity with

EN 60745.

Machine in protection class II

~ Alternating current

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

* Energy-rich, high-frequency interference can cause

fluctuations in speed. The fluctuations disappear,

however, as soon as the interference fades away.

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with

the values emitted by other power tools. The actual

values may be higher or lower, depending on the

particular application and the condition of the tool or

power tool. In estimating the values, you should also

include work breaks and periods of low use. Based

on the estimated emission values, specify protective

measures for the user - for example, any organisa-

tional steps that must be put in place.

Vibration total value (vector sum of three directions)

determined in accordance with EN 60745:

h, D

= Vibration emission value

(drilling into metal)

h,D

= Uncertainty (vibration)

Typical A-effective perceived sound levels:

=Sound pressure level

=Acoustic power level

, K

= Uncertainty

Wear ear protectors!

8. Cleaning, Maintenance

9. Troubleshooting

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical Specifications

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo BE Partner Edition Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info