Bedienungsanleitung Metabo BW 600 (Seite 13 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

451417

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

− System impedance Z

max.

at the

interconnection point (house

service connection) 0.35 Ohm

maximum.

Note:

Check with your local Electricity

Board or electrician if in doubt whether

your house service connection meets

these requirements.

Position power supply cable so it

does not interfere with the work and

is not damaged.

Protect power supply cable from heat,

aggressive liquids and sharp edges.

Use only rubber-jacketed cable of suf-

ficient lead cross section as exten-

sion cable.

Do not pull on power supply cable to

unplug.

Changing the direction of rota-

tion!

Depending on phase sequence it is

possible that the motor will turn in the

wrong direction. This can lead to the

log being hurled away when attempt-

ing to make a cut. Therefore the rota-

tional direction must be checked

every time the machine is connected

to a different outlet. With an incorrect

direction of rotation the phase

changer in the machine's CEE plug

needs to be changed-over:

1. Install machine ready for work

and connect it to the power

mains.

2. Start machine and immediately

turn OFF again.

3. Check the saw blade's direction

of rotation from the left-hand side

of the saw. The saw blade must

rotate clockwise.

4. If the saw blade rotates counter-

clockwise, unplug the power

cable at the saw.

5. Using a flat blade screwdriver,

push the phase changer inside

the machine's plug down and turn

it by 180°.

Caution!

Do not attempt to turn the

phase changer at the contact pins!

Please take note of the following

safety information before operating

the machine!

Also follow the safety instructions

given at the beginning of this manual!

Hazard generated by machine

defects!

Before starting work, check to see that

the following are in proper working order:

• Saw blade (firmly mounted? undam-

aged? sharp? sufficient distance to

other parts?)

• Blade guard (undamaged? distance

to saw blade sufficient? does exten-

sion arm return to starting position

automatically?)

• Feed rocker (must automatically

return to the starting position)

• Power cable, power cable plug and

switch (if damaged, have replaced

to a qualified electrician)

• Motor brake (after switching OFF

maximum 10 seconds post-running

of saw blade)

Risk of injury by inhaling wood

dust!

Dust of certain timber species (e.g. oak,

beech, ash) can cause cancer when

inhaled:

• Work only out of doors.

• When working, take care that as lit-

tle wood dust as possible will get

into the surroundings:

• remove wood dust depositions in

the work area (do not blow away!).

Hazard generated by insuffi-

cient personal protection gear!

• Wear suitable work clothing, provid-

ing protection against falling logs.

• Wear hearing protection.

• Wear safety glasses.

• Wear dust mask.

• Wear non-slip safety shoes.

• Take care that no parts of your body

or clothing are caught by rotating

components (do not wear ties or

loose fitting garments; contain long

hair with a hairnet).

Risk of personal injury and

crushing by moving parts!

• Do not operate the machine without

installed guards.

• Keep sufficient distance to driven

components when operating the

electric tool.

• Do not remove small cutoffs, splin-

ters, etc. from near the rotating saw

blade by hand.

• Always use the feed rocker to feed

the logs to be cut.

• Always hold the feed rockers with

boths hands at its handle.

• Assume proper operating position:

− at the front of the saw;

− in front of the saw;

− offset to the line of cut.

• After each cut return the feed rocker

completely to its starting position.

Hazard generated by pieces of

wood being hurled away!

• Always place curved logs on the

feed rocker with the curved side fac-

ing the saw blade.

• Do not jam the log to be cut.

• Do not attempt to stop the saw

blade by pushing the workpiece

against its side.

• Always use sharp saw blades.

• If in doubt, inspect the logs for for-

eign matter (e.g. nails or screws).

• Never cut several logs at the same

time – and also no bundles contain-

ing several individual pieces. Risk of

personal injury if individual pieces

are caught by the saw blade uncon-

trolled.

6.1 Cutting

1. Start machine and let the motor

reach full speed.

2. Place a log on the feed rocker.

3. To make the cut, push the feed

rocker (16) with both hands at the

handle towards the saw blade:

− Exert only so much pressure that

the motor speed does not fall off.

− Push feed rocker forward until it

hits the stop.

4. Return feed rocker completely to

the starting position.

Note:

If the log was not completely sep-

arated, turn it over and repeat the cutting

operation from the opposite side (revers-

ing cut).

6. Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo BW 600 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info