Bedienungsanleitung Metabo DSE 300 INTEC (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595419

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Pull the base-plate (10) downwards.

At the same time, turn the base-plate (10) in the

desired direction.

Release the base-plate (10) or turn on until it

engages in position.

7.5 Removing and refitting the base-plate

Removing

Pull off the “cling-fit” sanding sheet.

Slacken off the hexagon socket-head screw (12)

with the hexagon socket-head key (6) and unscrew.

Remove the spring (11) from the recess in the

base-plate (10).

Remove the base-plate (10).

Refitting

Locate the base-plate (10) so that it engages in

position and cannot be turned.

Insert the spring (11) in the recess in the base-

plate (10).

Screw in and fully tighten the hexagon socket-

head screw (12) with the hexagon socket-head

key (6).

7.6 Removing and refitting the paper dust

bag holder

If you are not using an external suction unit but

are relying on your sander/scraper’s integrated

vacuum extraction feature, fit the paper dust bag

holder along with the dust filter and cover .

DSE 300: optional accessory

DSE 300 Intec: standard equipment

Removing

Press the catch hook on the paper dust bag

holder (9) and pull the dust bag holder out towards

the back.

Refitting

Push down the catch hook on the paper dust bag

holder (9) and push the cassette fully home until it

locks in position in the sander/scraper.

The catch hook must engage properly on the tool!

7.7 Changing the dust filter

Remove the paper dust bag holder (9).

Remove the cover (7).

Lift out the dust filter (8).

Push a new dust filter (8) into the paper dust bag

holder (9) far enough so that it no longer

protrudes.

Refit the cover (7).

Refit the paper dust bag holder (9).

7.8 Removing and refitting the vacuum

extraction nozzle

If you wish to use an external suction unit, fit the

vacuum extraction nozzle to the sander/scraper.

DSE 300: standard equipment

DSE 300 Intec: optional accessory

You can then connect a Metabo all-purpose

suction unit or some other suitable extraction

device to the vacuum extraction nozzle.

If you do not have a vacuum extraction device

fitted to the vacuum extraction nozzle (3), you

must locate the plug (5) to block off the extraction

channel.

Removing

Use the hexagon socket-head key (6) to slacken

off the hexagon socket-head screw (4) and

unscrew.

Pull the vacuum extraction nozzle (3) out towards

the back.

Refitting

Push the vacuum extraction nozzle (3) in from the

back until it is seated fully home in the

sander/scraper.

Use the hexagon socket-head key (6) to insert the

hexagon socket-head screw (4) and tighten fully.

8 Tips and Hints

Do not exert any great pressure as you guide the

sander/scraper over the surface to be processed.

Pressing harder does not increase the tool’s

performance.

Change worn “cling-fit” sanding sheets in good

time to ensure the desired results.

Change the dust filter at regular intervals to

ensure maximum dust extraction.

ENGLISH

02_DSE_300_ENG_0410.qxp:02_DSE_300_ENG_0410.qxp 07.04.2010 15:45 Uhr Seite 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo DSE 300 INTEC Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info