Bedienungsanleitung Metabo E 140 SP (Seite 9 von 39) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

658069

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

ENGLISH

Approach the weld metal with the elec-

trode.

Contact of the electrode to the weld

metal causes a short-circuit, the welding

current is reduced. The material is

heated up and a short arc generated.

By lifting the electrode the arc is started

and will burn at the set welding current

(not applicable for E 140 SP/Plus).

5.3 Shutting down

1. Set master switch to “0”.

2. Disconnect the earth cable from the

workpiece.

3. Unplug the power cable.

This welding machine contains no user-

serviceable parts.

Depending on dust accumulation the

dust should be blown out from the

machine with dry and oil-free com

pressed air every 4 - 6 months.

Periodically perform a check for visible

damage.

Contact a qualified electrician if any of

the cables are damaged.

For special welding tasks the following

accessories are available at specialised

dealers – see back cover for illustrations.

These accessories have been tested

with the machine and ensure operation

without any problem.

A TIG welding torch

SR 17 V for E 130/E 150,

E 140 SP/Plus

required for TIG welding.

1) 2 m torch leads

2) 4 m torch leads

3) 8 m torch leads

B TIG welding torch

SR 26 V for E 170Si ,

required for TIG welding.

1) 4 m torch leads

2) 8 m torch leads

C Pressure regulator with 2 pressure

gauges

1) without stop valve

2) with stop valve

D Welding visor

1) helmet

2) automatic screen

Danger!

Repairs to power tools must be

carried out by qualified electricians

only!

Welding machines in need of repair can

be sent to the service centre of your

country. Refer to the spare parts list for

the address.

Please attach a description of the fault to

the power tool.

The machine's packaging can be 100 %

recycled.

Worn out power tools and accessories

contain considerable amounts of valua-

ble raw and rubber materials, which can

be recycled.

These instructions are printed on paper

produced with elemental chlorine free

bleaching process.

The welding machine is equipped with

an overload protection. It will automati

cally turn OFF in case of excessive oper-

ating temperatures and under- or over-

voltage.

− The “Fault” indicator light is flashing.

In case of an excessive operating tem-

perature:

− DO NOT turn the machine OFF,

in order for the fan to cool the

machine down faster.

− The “Fault” indicator light will go out

when the temperature has fallen off

to normal levels.

You can now continue welding.

In case of under- or overvoltage:

− Check the mains voltage.

6. Maintenance

7. Available Accessories

8. Repairs

9. Environmental Protection

10. Disorders

11. Trouble Shooting

Brittle or porous weld seam

Workpiece not

clean?

Remove rust,

grease or other

contamination

prior to welding.

No welding current

Earth cable mak-

ing poor contact?

Check earth

cable for proper

contact.

The “Fault” indi-

cator light is

flashing.

Check mains

voltage and fan

Electronics

faulty?

Contact

service centre.

No function of machine

Supply circuit

fuse blown or

cut-out?

Replace or turn

ON again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo E 140 SP Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info