Bedienungsanleitung Metabo HE 23-650 Control (Seite 11 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599607

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH en

Press the buttons (6) to set the

temperature.

Briefly press the "+" /"-" buttons to

increase or lower the set value in 10°

steps. Press the buttons longer to change the value

faster.

Notes:

Triangles are displayed when

the desired temperature is

being set.

If the desired temperature is

set, the blower (depending on

the selected speed/air volume)

needs a few seconds to reach the set value. The

triangles flash during this period.

The actual temperature is

measured at the nozzle outlet.

The triangles disappear when

the desired temperature has been reached.

When the hot air gun is switched off, the last value

set is retained.

Setting air volume:

Press the buttons (7) to set the air volume

or the fan speed.

Program operation:

Four programs for the most frequent types of

work are set in the factory. Press the "P"

button for program operation. A for

program 1 appears in the display. Press the

program button again to reach the programs

, and . Press the button again to return to

normal operation.

Program 1: Forming plastic pipes

Program 2: Welding plastic pipes

Program 3: Removing paint

Program 4: Soft soldering

(For technical data, see chapter 12.)

Changing programs and saving:

The values in the four programs can be

changed and saved. To do this, first press the

program button "P" until the program to be

changed is displayed. Set the desired air

volume and temperature. Then push the save

button (10) until the symbol in the display

disappears (approx. 5 seconds). The entered

values are now saved in the program.

Note:

- To return from program operation to the normal

function, press the program button (8) until the

program symbol in the display (9) has

disappeared.

- The factory settings of the programs are listed in

chapter12..

6.4 Stationary operation

If you wish to use the hot air gun as a stationary

tool, ensure that it is placed on a safe, anti-slip

and clean base.

To use the hot air gun in stationary operation, place

it on the anti-slip bases (5).

The air inlet (3) with grid

must be free of foreign

bodies.

Clean the air inlet (3)

if necessary.

Thermal protection

The tools are equipped with 2-stage thermal

protection:

1. * A thermo switch switches off the heater in case

of excessive interference in the air outlet of the

blow-out opening (heat accumulation). However,

the blower continues running. When the blow-out

opening is free again, the heater cuts in again

automatically after a short while. The thermo switch

can also trip after the tool is switched off. In this

case, after the tool is switched on again it takes

longer than usual until the temperature at the blow-

out opening is reached.

* does not apply to HE 20-600, H 16-500

2. The thermal fuse switches the tool off completely

in the event of overloading.

Short-term voltage drops

Switching on the machine reduces the voltage

briefly. Unfavourable mains power conditions may

have a detrimental effect on other machines.

Network impedances less than 0.4 ohms should not

cause malfunctions.

Use only genuine Metabo accessories.

If you need any accessories, check with your

dealer.

For dealers to select the correct accessory, they

need to know the exact model designation of your

power tool.

For possible accessories, refer to the illustrations

on page 3.

A Flat spray nozzle

Drying, removal of old paint coats

BSpray nozzle

Removal of paint coats on window frames

C Reflector nozzle

Heating of plastics prior to forming; shrink fitting

of shrinking hoses

D Slotted nozzle

Lap welding of PVC fabrics and foils

E Reducing nozzle (only HE 20-600, HE 23-650

Control) for precise heating of specific points

(e.g. solders and welds)

FWelding shoe

G Plastic welding wire

for welding work

For a complete range of accessories, see

www.metabo.com or the main catalogue.

7. Servicing

8. Troubleshooting

9. Accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo HE 23-650 Control Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info