Bedienungsanleitung Metabo HS 6000 (Seite 14 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

451433

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

led by means of the two operating

levers. There are three possible

actions:

− Press both operating levers

downward – The work cycle

starts, and the splitting knife

moves downward to split the log.

− Press only one operating lever

downward – The splitting knife

stops.

− Release both operating levers –

The splitting knife moves back

upward to its start position.

The splitting knife stops automati-

cally in the upper or lower position

(end of travel).

5. When the log is split, release both

operating levers – The splitting knife

then returns to its start position.

6. Remove the split pieces of wood,

and place them off to the side and

out of the immediate work area –

Now you are ready to continue split-

ting.

7. If you do not intend to continue

working immediately, turn off the

splitter by pressing the RED

switch (16).

6.2 Changing the start posi-

tion of the splitting knife

In addition to the height options provided

by the three pivoting support tables, you

can also change the upper start position

of the splitting knife to even better

accommodate the length of the log to be

split. With the upper start position for the

splitting knife set lower, the knife

requires less time to approach the work.

The results in a shorter work cycle.

Lowering the upper start position

1. Turn on the splitter (press the

GREEN switch).

2. Press both operating levers down-

ward – As soon as the splitting knife

has reached the new desired height,

release the right lever.

3. Switch machine OFF

4. Loosen the wing nut (18) and pull

out the control rod (17) until it

reaches the stop. Retighten the

wing nut.

The upper start position is now set

as desired. Continue to operate the

splitter as previously described.

Resetting the splitting knife to its

upper start position

1. Switch machine OFF.

2. Loosen the wing nut (18) and push

in the control rod (17) until it reaches

the stop. Retighten the wing nut.

The upper start position is now reset

at the maximum height.

Danger!

Prior to all servicing:

− Switch machine OFF.

− Unplug power cable.

DANGER! Directly after stopping the

splitter, the hydraulic oil and hydrau-

lic system parts may be hot! Let the

splitter cool down before any servic-

ing.

Avoid direct skin contact with hydrau-

lic oil. Wear protective gloves.

Dispose of hydraulic oil in an environ-

mentally friendly manner at a proper

waste oil collection point.

When topping up or changing the

hydraulic oil, be sure to use only

approved types of oil (see "Technical

Specifications").

• Replace damaged parts, especially

safety devices, only with genuine

replacement parts since parts not

tested and approved by the equip-

ment manufacturer can cause

unforeseeable damage.

• Repair and maintenance work other

than described in this section should

only be carried out by qualified spe-

cialists.

• Check that all safety devices are

operational again after each service.

7.1 Changing the hydraulics

fluid

1. Move the splitting knife all the way

down, and turn off the splitter.

2. Before starting, place a suitable col-

lecting vessel in position underneath

the draining bolt (19). This vessel

must have a capacity of at least 7 lit-

ers.

3. Undo and remove the draining bolt

(19) and allow the oil to drain com-

pletely.

4. Refit the draining bolt (19) ) together

with the seal and tighten.

5. Unscrew the dipstick (20) and fill the

reservoir with hydraulic oil.

6. Checking the oil level. With the split-

ter column retracted the oil level

must be between the upper and

lower marks.

7. Screw the dipstick back in and

tighten it.

7.2 Clean the oil filter.

1. Undo the hollow bolt (23) on the

pump case (21) and, taking care not

to lose the three ring-seals (24) with-

draw the bolt from the hose connec-

tor (22).

7. Care and maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo HS 6000 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info