Bedienungsanleitung Metabo HS 8000 (Seite 15 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

451435

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

7.1 Cleaning the oil filter /

Changing the hydraulic

oil

Before cleaning the oil filter, first drain

out the hydraulic oil. After cleaning the

filter, you can reuse the same oil,

depending on how long the it has been

in service (see "Service Intervals").

1. Move the splitting knife all the way

down, and turn off the splitter.

2. Select a suitable, clean drain pan

with a capacity of at least 7 liters

and place it under the oil suction line

fitting (29).

3. Release the oil suction hose by

loosening the collar nut (28) at the

oil suction line fitting.

4. Unscrew the oil suction line fitting.

5. Let the oil drain out completely.

6. Unscrew the oil filter (30) from the

suction line fitting (29) and clean it in

a suitable petroleum-based solvent

such as kerosene (Be sure to thor-

oughly remove traces of the solvent

from the filter before reinstalling it).

7. Screw the oil filter back into the oil

suction line fitting.

8. Screw the oil suction line fitting back

in with its gasket and tighten it.

9. Reinstall the suction hose at the oil

suction line fitting.

10. Unscrew the dipstick (31) and fill the

reservoir with hydraulic oil.

11. Checking the oil level. With the split-

ter column retracted the oil level

must be between the upper and

lower marks.

12. Screw the dipstick back in and

tighten it.

7.2 Machine storage

1. Lower the splitter column fully, and

with it in this position, turn off the

splitter.

2. When not in use, store the splitter so

that it cannot be started by unau-

thorized persons (the ON/OFF

switch can be secured with a pad-

lock).

Caution!

Do not store the splitter unpro-

tected outdoors or in a damp environ-

ment.

7.3 Maintenance

Before each use

Check the ON/OFF switch and the two-

hand controls for proper function.

Check the hydraulic hoses for damage

(cuts, chafing and kinks).

Check the lubrication system for leaks.

After the first hour of operation

Clean the oil filter.

Every 50 hours of operation

Clean off all moving/articulated parts

(joints, hinges and splitter column

guides) with suitable cloths and then

lightly re-oil them.

Check the oil level. With the splitter col-

umn retracted, the oil level must be

between the upper and lower marks.

Every 200 hours of operation

Clean the oil filter.

Every 1000 hours of operation

Replace the hydraulic oil.

For special tasks the following accesso-

ries are available at your specialized

dealer – see back cover for illustrations:

A Four-way splitting wedge:

This accessory splits logs into four

pieces in one work cycle. With it,

the amount of work cycles can be

cut in half, significantly reducing

overall splitting time.

B Hydraulic oil for topping up and

refilling.

C Care and Maintenance Spray

For removing resin residue and pre-

serve metal surfaces.

Danger!

Repairs to electric tools must

be carried out by qualified electri-

cians only!

Electric tools in need of repair can be

sent to the service centre of your coun-

try. Refer to the spare parts list for the

address.

Please attach a description of the fault to

the electric tool.

Danger!

Before carrying out any repair

service or maintenance work, always:

− Switch machine OFF

− Unplug power cable

Check that all safety devices are

operational again after each fault

service.

Motor does not run

No supply voltage:

− Check cables, plug, outlet and

mains fuse.

Mains voltage too low:

− Use power cable of sufficient wire

gauge (see "Technical specifica-

tions").

No-voltage release solenoid tripped by

temporary power failure:

− Switch on again.

Overload protection tripped:

Let motor cool down for approx. 10 min-

utes, then start motor again.

Motor runs, but the splitting wedge

does not move

Phase sequence changed at the phase

changer:

− Change direction of rotation (see

"Power connection").

Low splitting force (ram force)

Splitter column guides are dirty:

− Clean the guides (see "Mainte-

nance").

28 29

8. Available accessories

9. Repairs

10. Trouble shooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo HS 8000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info