Bedienungsanleitung Metabo KFM 18 LTX 3 RF (Seite 15 von 108) (Alle Sprachen)

625654

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH en

7. To finish work: Remove the tool from the

workpiece, switch off machine. Let motor come

to a stop, put down machine.

9.1 Change indexable inserts

Regularly check the holder for the indexable inserts

(22). Repair/replace damaged or worn holders for

the indexable inserts.

Regularly check all indexable inserts (20). Change

damaged or worn indexable inserts.

Remove the battery pack from the machine /

pull the plug out of the socket before making

any adjustments, changing tools, carrying out

maintenance or cleaning.

Indexable inserts, holders for indexable

inserts, workpiece and chips can be hot after

work. Wear protective gloves.

Turn/replace blunt indexable inserts or inserts

where the coating is worn in due time. Blunt

indexable inserts increase the risk of the machine

getting jammed and climb out.

Always turn or replace all indexable inserts.

Use only indexable inserts approved by

Metabo. See the Accessories Section.

1. By turning the adjustment ring (13) to the stop,

unscrew the holder for the indexable inserts (22)

as much as possible - this provides good access

to the indexable inserts.

2. Press in the spindle locking button (2) and turn

the holder for the indexable inserts (13) by hand

until the spindle locking button (2) engages.

Keep the spindle locking button (2) pressed.

3. Unscrew the fastening screw (21) and remove

the indexable insert (20).

4. Turn the indexable insert or, if all blades are

blunt, replace the indexable inserts.

5. Fix again the indexable inserts (20) with a

fastening screw (21). Torque: 5 Nm.

6. Turn the adjusting ring (13) in the opposite

direction, so that the holder for the indexable

inserts (22) is again in its normal work range. (So

that the maximum permitted chamfer height is

not exceeded, see chapter Technical

Specifications).

9.2 Replace ball bearing stationary seal ring

(only if required):

Regularly check the ball bearing stationary seal ring

(19) for smooth running. Replace defective ball

bearing stationary seal ring. (order no.: 316093300)

1. Remove screw (18) and remove ball bearing

stationary seal ring.

2. Put new ball bearing stationary seal ring (19) in

place and add screw (18), tighten firmly.

9.3 Adjust scale (only if required):

The graduated ring (12) comes properly set from

the factory.

If indexable inserts are to be used for radii or if the

settings should have been misaligned, the scale

has to be adjusted as follows:

1. Lift the adjustment ring (13) and turn in such a

way that the indexable insert (20) does not

remove any material. (chamfer height = 0 mm)

2. Loosen the two clamping screws (12).

3. Turn the graduated ring (12) until the chamfer

height 0 mm is shown.

4. Tighten the two clamping screws (12).

5. Carry out trial cut.

Chips and particles can deposit at the cutter head.

This can lead to blockage of the cutter head.

Regularly clean the cutter head and its

surroundings and remove chips and particles.

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of the

power tool. Conductive build-up can impair the

protective insulation of the power tool and cause

electrical hazards.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

11.1 Mains powered machines:

- Overload protection: There is a MAJOR

reduction in load speed. The motor temperature

is too high! Allow the machine to run at idle speed

until it has cooled down.

- Overload protection: There is a MINOR

reduction in load speed.

The machine is

overloaded. Reduce the load before continuing to

work.

- Metabo S-automatic safety shut-down: The

machine has SHUT DOWN by itself. If the slew

rate of the current is too high (for example, if the

machine suddenly seizes or kickback occurs), the

machine switches off. Switch off the machine

using the slide switch (4). Switch it on again and

continue to work as normal. Try to prevent the

machine from seizing. See chapter 4.1.

- Restart protection: The machine does not

start. The restart protection is active. If the mains

plug is inserted with the machine switched on, or if

the power supply is restored following an

interruption, the machine does not start up. Switch

the machine off and on again.

11.2 Cordless machines:

- The electronic signal display (7) lights up and

the load speed decreases. The temperature is

too high! Run the machine in idling until the

electronics signal indicator switches off.

9. Maintenance

10. Cleaning

11. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KFM 18 LTX 3 RF Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info