Bedienungsanleitung Metabo KFM 9-3 RF (Seite 14 von 108) (Alle Sprachen)

625653

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISHen

1. Place the parallel guide/ripping fence (16) as

shown.

2. Screw knurled screw (15) into one of the

threaded holes.

3. Set the parallel guide/ripping fence (16) by

turning to the desired angle.

4. Firmly tighten the knurled screw (15).

Remove the battery pack from the machine /

pull the plug out of the socket before making

any adjustments, changing tools, carrying out

maintenance or cleaning.

Indexable inserts, holders for indexable

inserts, workpiece and chips can be hot after

work. Wear protective gloves.

Danger of crushing! Wear protective gloves.

7.1 Adjust scales (only when required)

The scales (12), (14) come with the correct settings

from the factory. However, should they be adjusted,

see chapter 9.3.

7.2 Set chamfer height

Read the set chamfer height

at the graduated

scale (12):

1. Read the set chamfer height at the graduated

scale (12). See illustration: Set chamfer height =

0.7 mm.

(The scale (14) is used for the rough orientation

during the setting process).

Change the chamfer height by turning the adjusting

ring:

2. Push the adjusting ring (13) downwards and

turn.

The chamfer height can be set in 0.1 mm (0.00394“)

steps. Each full rotation results in a change of the

chamfer height by 3.0 mm (1/8“).

Remove max. 3.0 mm per cutting operation.

Create larger chamfer heights in several

cutting operations. Do not exceed the maximum

permitted chamfer height (see chapter Technical

Specifications).

3. Carry out trial cut.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid unintentional start-up of the machine:

always switch off the machine, if the plug is

pulled from the mains socket or if there was a power

cut / if the battery pack was removed from the

machine.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

Machines with slide switch:

Switching on: Push the sliding switch (4) forward.

For continuous activation, now tilt downwards until

it engages.

Switching off: Press the rear end of the slide

switch (4) and release it.

8.2 Working Directions

1. Check indexable inserts (20). Change damaged

or worn indexable inserts.

2. Set the chamfer height (see section 7.2).

3. Always hold the machine with both hands on the

intended handles, take a secure stance and

concentrate on the work.

4. First switch on, then place the machine with the

support surface (17) onto the workpiece and

only then put the tool close to the workpiece.

5. When cutting, always work against the run of the

disc (see illustration). Otherwise there is the risk

of a kickback. Guide the machine evenly at a

speed suitable for the material being processed.

Do not tilt, apply excessive force or sway from

side to side.

6. Guide the machine in such a way that the parallel

guide (16) is in contact with the workpiece. If you

work without parallel guide: Guide the machine

in such a way that the ball-bearing stationary

seal ring (19) is in contact with the workpiece.

7. Setting

8. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KFM 9-3 RF Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info