ENGLISHen
16
Cutting the workpiece:
1. Loosen locking lever (11) of the turntable and
loosen safety catch (12) .
2. Set the desired angle.
3. Tighten the locking button (11) of the
turntable.
4. Cut workpiece, as described for "Straight
cuts".
9.3 Inclined cuts
Starting position:
–T (25) pulled out.
–S
– Cutting depth limitation (52) deactivated.
– Turntable is in 0° position, locking (11)
for turntable is tightened.
– Pulling device at the very rear.
–S (13) of the pulling device has been
loosened.
Cutting the workpiec
1. Loosen the locking (23) for the
inclinatio
2. Slowly tilt the swivel arm into the desired
position.
3. Tighten the locking lever (23) for the
inclinat
4. Cut the workpiece, as described for "Straight
cuts".
9.4 Double mitre cuts
Note:
The double mitre c
and inclined cut. Thans, the workpiece is cut
at an angle to the rear contact edge and at an
angle to the top.
Danger!
With a double mitre cut, the saw blade is easier
accessible due to th
results in a higher risk of injury. Always keep
sufficient distance to the saw blade!
Starting position:
–T (25) pulled out.
–S
– Cutting depth limitation (52) deactivated.
– Lock the turn table in the desired position.
– Swivel arm inclined at desired angle to the
workpiece surface and locked.
–S (13) of the pulling device has been
loosened.
– Pulling device at the very rear.
Cutting the workpiece:
Cut the workpiece, as described for "Straight
cuts".
9.5 Cutting grooves
Note:
The cutting depth limitation together with the
pulling device permits
does not result in a
of a certain depth is effected in the workpiece.
Risk of kickback!
When cutting gr
that no lateral pressure is exerted on the
blade. Otherwise, the saw head might
kick back! Use a clamping device when cutting
grooves. Avoid lateral pressure on the saw head.
Starting position:
–T (25) pulled out.
–S
– Swivel arm inclined at desired angle to the
workpiece surface and locked.
– Lock the turn table in the desired position.
–S (13) of the pulling device has been
loosened.
– Pulling device at the very rear.
Cutting the wo
1. Set the cutting depth limitation (51) to t
desired cutting depth and fix with counter
2. Loosen safety lock (27) and swivel saw h
downwards toe set cutting depth:
3. Effect trial cut.
4. If required, repeat steps 1 and 3 until the
desired cutting depth has been set.
5. Cut the workpiece, as described for "Straight
cuts".
Danger!
Prior to all mainten
mains plug or remove the detachable battery
pack (34) .
– Repair and maintenance work other than
described in this section sh
out by qualified
– Replace damaged par
installation
approved by the equipm
cause unforeseeable damage.
– Check that all safety devices are operational
again after
10.1 Saw bl
Risk of burning!
Directly after cutting the saw blade can be very
hot. Let a hot saw blade cool down. Do not clean
the hot saw blade with combustible liquids.
Risk of injury, even with the blade at
standstill!
When loosen
screw (44) the retractable blade guard (6) has to
be swivelled over the saw blade. Wear gloves
when changing blades.
1. Pull the mains plug remove the detachable
battery pack (34) .
2. Put the saw head in the upper position.
3. Lock saw blade: press the locking button and
turn the saw blade with the other hand until the
locking button engage
locking button.
4. Remove the tensioning scr
(44) on the saw blade shaft with Alle
(14) in cln (left-hand thread!).
5. Loosen safety lock (27) (only for m
powered devices) and push the retractable
blade guard (6) upwa
6. Carefully remove outer flange (45) and saw
blade (46) from the saw blade shaft and close
again the retractable blade g
Danger!
Do not use cleaning agents (e.g. to remove resin
residue) that could corrode the light metal
components of the saw; the stab
would be adversely affected.
7. Cleaning
– Saw blade shaft (49) ,
– saw blade (46) ,
–o (45),
–i (48).
Danger!
Place inner flange properly! If this is not the case,
the saw can block or the saw bla
loose. The inner fl
the ring groove pointowards the saw blade and
the flat side to the motor.
8. Put on inner flange (48) .
9. Loosen safety lock (27) (only for m
powered devices) and push the retractable
blade guard (6) upwa
10.Plac
direction of rotaen from the left (open)
side, the arrow on the saw blade has to
correspond to the dire (47)
on the saw blade
Danger!
Use only saw blades, which fulfil the requirements
and specificationsed in these operating
instructions.
Use only saw blades designed for the maximum
speed (see "Technical Specificat
unsuitable or damaged saw blades parts
used, parts can be ejected due to centrifugal
force in an explosive-type manner.
Saw blades intended for c
materials have to conform to EN 847-1.
Do not use:
– saw blades made of high-alloy speed steel
(HSS);
– damaged saw blades;
– cut-off wheel blades.
Danger!
– Mount saw blade using
– Do not use loose-fittireducing ri
blade could work loose.
– Saw blades h
that they do not wobble or run out of balanc
and cannot work loose during
11.C (6).
12.Slide on (45) – The flat side has
to point towards the motor!
13.Put nsioning
(44) in anti-clockwise direction (left-
thread) and tighten by hand.
14.Lock saw blade: press the locking button (18)
and turn the saw blade with the other ha
until the locking button enga
the locking button.
Danger!
– Do not extend the hex
– Do not tighten the tensioning scre
the hexagon wrench.
15.Firmly tighten the tensioning screw (44) using
the hexagon (14) .
16.Cen the safety lock (27)
(only for mains-powered devices) and fold the
saw downwards
– when folding down the retractable blade
guard, it has to provide free access to the saw
blade without touching other parts.
– When folding the saw upwards into the
starting position, the retractable blade guard
has to cover the saw blade automatically.
– Rotate the saw blade manually. You should be
able to rotate the saw blade into any possible
position with
10.2 Table i
Danger!
With a damaged table insert (10) there is a ris
small parts getting stuck bet
saw blade, blocking the saw blade. Replace
damaged table inserts immediately!
1. Remove screws at tab
rotate turntable and incline saw head to be
able to reach the screws.
2. Remove table insert.
3. Insert new table insert.
4. Tighten the screws at the table insert.
10.3 Adjust parallel g
1. Loosen Allen screws (50) .
2. Adjust the parallel guide/ripping fence (26) in
such a way that it is exactly perpendicular to
the saw blade when the turntable engages in
the 0° position.
3. Tighten the Allen screws (50) .
10. Care And Maintenance
