ENGLISHen
14
Observe th
material
application (e.g. o
regulations
Collect the generated particles at the source,
avoid deposits
Use the supplied dust collection unit and a
suitable extraction
particles enter the environment in an
uncontrolled way.
Reduce dust exposure with the following
measures:
– Do not direct the escaping particl
exhaust air stream at yourself or nearby
persons or on
– Use an extraction unit and/or air purifiers
– Ensure good venti
keep clean using a vacuum cleaner Sweepin
or blowing
– Vacuum or wash the protective clothing
blow, beat or brush
Hazard generated by modification of
the machine or use of parts not tested and
approved by the equi
Assemble tool in strict accordance with these
instructions
Use only parts approved by the equipment
manufacturer. This appli
– saw blades (for order numbers, refer to
chapter 12. Accessories).
– Safety devices.
– Cutting laser
– Illum
Do not change any p
Ensure that the speed indicated on the saw
blade is at leas
indicated on the saw.
Hazard generated by tool defects!
Before every use check tool for possible
damage: beforeg the tool all safety
devices, protective guards or slightly damaged
parts need to be checked for proper function as
specified. Check to see that all moving parts
work properly and do not jam. All par
correctly installed and fulfil all con
necessary to ensure perfect operation of the
unit.
Do not used any damaged or contorted saw
blades.
Risk of injury by noise!
Wear hearing protection.
Danger from blocking workpieces or
workpiece parts!
If blockage occurs:
1. switch machine o
2. Pull the mains plug or remove the detachable
battery pack,
3. wear gloves,
4. clear the blockag
4.2 Special safe
cordless machines:
Remove the battery pack from the machine before
making any adjus
maintainin
Protect battery packs from water and
moisture!
Do not expose battery packs to
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch contacts or shor
packs!
A slightly acidic, flammab
from defective Li-i
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
4.3 Symbols on the machine (depends
on model)
Read the operating instr
Never plac
blade.
Wear protective gogg
protecto
Never operate th
environment.
Laser radiation - Do not look
into the light beam.
LASER CLASS 2
4.4 Safety devices
Retractable blade gu
The retractable blade guard protects against
unintentional contact with the saw blade and from
chips flying about.
Safety lock (27)
Cordless tool
The machine can only be
switched on when the safety lock is
Mains-powered too
The retractable blade
guard opens and the saw can be
when the safety lock is activated.
Parallel guide/ ripping fence (
The parallel guide/ ripping fence prevents
workpiece c
process. Durinn, the parallel guide/
ripping fence
The additional profile (35) at the parallel guide/
ripping fence has to moved for inclin
after loosening the set screw (36) .
See page 2.
1 Closing the chip bag
2 Chip bag
3 Chip extraction nozzl
4 Laser beam egress point
5 Cutting
6 Retractable blade g
7 Longitudinal st
8T
9T
10 Table insert
11 Locking lever for turntable
12 Safety catch for stop positions of the turntable*
13 Set screw for pulling device*
14 Allen key / tool storage for Allen key
15 Work clamp
16 Table extension
17 Locking screw of the table width extension
18 Saw blade lock
19 Saw handle
20 Speed adjustment wheel *
21 Handle
22 Hook for cable winding
23 Locking lever for settin
24 Locking button (to extend the angle of
inclination by +/- 2 °)
25 Transport lock
26 Parallel g
27 Safety lock
28 On/off switch of the saw
29 On/off switch of the cutting laser
30 On/off switch o
31 Battery pack release button *
32 Capacity indicator b
33 Capacity and signal indicator *
34 Battery pack*
* depends on model / equipment
Install handle (21) if required (depending on
model)
Fix the handle (21) as
Install table width extension (16) if required
(depending on model)
1. Remove right and left table width extension
from the transport packaging.
2. Remove screws (37) at the guide rails of the
right and left table width extension.
3. Push the guide rails of the table width
extensions com
Insert the table width extension with folding
length guide (7) on the right side.
4. Lift the device at the front legs, carefully tilt it
backwards and put it down
over.
5. Tighten again the screws (37) at the guide
rails.
6. Take the front legs of the device, carefully tilt it
forwards and put down.
7. Set the desired table width and lock the
width extensio (17).
Installation
The device has to be mounted on a s
support for safe working.
– The support can be either a firmly mounted w
top or work bench.
– Even when machining rger workpieces the
device has to have a secure st
– Long workpieces mus
with suitable acces
Note:
For mobile use, the device can also be fixed to a
plywood or coreboard p
at least 19 mm thick) using screws. During use,
the panel has to be
screw clamps.
1. Fix device to the support using scre
2. Loosen transport lock (25) : Push saw head
slightly downwards
lock (25) .
3. Swivel saw head slightly upwards
Transport
1. Swivel saw head do
transport lock (25) .
2. Lock the pulling device in the front position
using the set screw (13) .
Caution!
Do not hold the saw at the protective installations
during transport.
3. Lift the device at the handle (21) and carry it.
7.1 On/Off switch motor (28)
Switching on the moto
Press the on/off switch and keep presse
Switching off the motor:
Let go of the on/off switch.
7.2 On/off switch cutting
illumina (30)
Switching on/ off the illumination of the cutting
line.
Danger!
Do not direct the light beam into the
people or animals.
Note:
Cordless da short break the cutting
line illumination goes off (s
automatically reactivated when resuming wo
case of a long
switches off automatically. Reactivation: Use
switch (30) .
5. Overview
6. Setup and transport
7. The device in detail
