ENGLISH en
15
7.3 On/off switch (29)
Switching on/off of the cutting laser.
The cutting laser marks a line to the left of the
saw's cut. Make a trial cut to become familiar with
the positioning.
Danger!
LASER BE
DO NOT LOOK INTO THE BEAM
LASER C
EN 60825-1:2014
P<1mW,λ =650nm
Note:
Cordless devi
laser goes off (slede) and is automatically
reactivated when resuming work. In
long break the cutting laser switches off.
Reactivation: Use switch (29) .
7.4 Setting the angle of inclination
After loosening th (23) , the saw
can be infini between 0° and
the left of the verti (40) .
Press the locking button (24) during the
adjustment process i
to 47° to the left of the vertical/ up to 2° to the right
of the vertical.
Danger!
In order for the angle of inclinatio
when cutting, the locking lev (23) of the swivel
arm has to be tightened.
You can adapt the position of the locking lever
according to your
lever, turn and push in the desired position and let
engage.
7.5 Turntable
After loosening th (11) and
activating the safety catch (12) , the turntable can
be turned by 47° to the left or by 47° to the right
for mitre cuts. In this manner the cutting angle to
the support edge of the workpiece is
Danger!
In order for
cutting,
(11)
of the turntable has
to be tightened (also in the sto
7.6 Pulling device
Using the pualso larger workpieces
with greater cross sections can be cut. The
pulling devi for all types of cuts
(straight cuts, mitre cuts, slanted cuts
mitre cuts, and cutting of groo
If the pulling device is not required, lock the
pulling device i position using the set
screw (13) .
7.7 Cutting depth limitation
Together with the pulling device the cutting depth
limitation (51) permits the cuttin
Turn the set screw and fix with the counter nut.
The cutting depth limitation can be deactivated,
the parallel guide (52) is pushe
7.8 Setting the speed
only for KGSV 216 M,
KGSM 216 Vario Max)
Select the speed at the setting wheel (20) . See
table for recommended setting wheel positions.
Wood: 3 - 6
Aluminium: . .
Plastic: 1 - 3
8.1 Connect chip sack / c
extraction unit
Danger!
Dust of certain timber species (e.g.
ash) can cause canc
– On
installed dust sack.
– In addition, use a dust mask, as not all saw dust
is collected or extracted.
– Regularly empty the dust sack. Wear a dust
mask while emptying the
If you operate the device with the supplied dust
sack:
Attach the dust sack (2) to the chip extraction
adapter nozzle (3) . Ensure that the closure (1)
of the dust sack
If you connect the device to a dust extraction unit:
Use a suitable adapter to connect it to the chip
extractiole (see chapter 12.
"Accessories").
Ensure that the dust extraction unit meets the
requirements stated in chapter 16. "Technical
Specifications".
Observe the dust collector's operating
instructio
8.2 Installing the workpiece clamping
device
The workpiece clamping device (15) can be
installed in two po
–F
workpieces:
Insert the workpiece clamping device into the
rear drilling (38) of the table.
– For narrow
workpieces:
Insert the workpiece clamping device into the
front drilling (39) of the table.
8.3 For mains powered machines only
Danger! High voltage
Operate machine only on a power source meeting
the following requir
"Technical Specifications"):
– Mains vstem frequency must
conform to the voltage and frequency shown on
the machine´s rating label;
– fuse protection by a residual current operated
device (RCD) of 30 mA sensitivity;
– outlets properly installed, earthed or groun
and tested.
Position pow
interfere with the work and is not damaged.
Use only rubberextension cables with
sufficient lead cros 1.5 mm
2
).
Use extension cables for outdoor areas. When
working outdoors, on
marked extension cable approved for this
purpose.
Avoid accidental start-u
switch is
the socket.
8.4 For cordless machines only
Avoid accidental start-u
battery pack, make sure
switched o
Battery pa
Charge the battery pack (34) before use.
If performan,
pack.
The ideal storage temperature is
and 30°C.
Li-Ion battery packs "Li-Power" have a ca
and signal indicator (33) :
- Press the button (32) , the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the batt
Removal:
Press the battery pack release button
(31) and pull out the battery pack (34) towards the
rear.
To insert:
Slide the battery pack (34) in until it
engages.
Before starting work, check to see that the
following ar
Assume proper op
– at the front of the saw;
– in front of the saw;
– next to the line of cut.
Danger!
If possible, fix the workpiece using the workpiece
clamping device (15) .
Danger of crushing!
When inclining or
reach into the hinge area or below the device!
Hold the saw head during in
Use during work
– workpiece support – for long workpieces, if
otherwise workd fall off the table
after cutting;
– dust sack or dust ex
Cut only workpieces of dimensions that allow
safe and secure holding while cuttin
Always hold the workpiece down on the table
and do not jam it. Do not attempt to stop the saw
blade by puspiece against its side.
Risk of personal injur
blocked.
9.1 Straight cuts
Starting position:
–T (25) pulled out.
– Saw head swivelled upwards.
– Cutting depth limitatio (52) deactivated.
– Turntable is in 0° position, locking button (11)
for turntable is tightened.
– The inclination o
0° , locking lever (23) for inclined position is
tightened.
– Pull
–S (13) of the pulling device has been
loosened.
Cutting the wo
1. Push the workpiece against t
ripping fencep using the workpiece
clamping device (15) .
2. For wider workpieces: pull the saw head
forwards (towards the oper
device).
3. Activate the safety lock (27) ,press on/off
switch (28) and keep pressed.
4. Slowly lower the
way down and, i
rear (away from the operator). During the
sawing process press on the workpiece jus
enough for the motor speed not to lower too
much.
5. Cut the workpiece in one operation.
6. Release the on/off switch (28) and slowly let
the saw head swivel back into the upper
starting position.
9.2 Mitre cuts
Starting position:
–T (25) pulled out.
– Saw head swivelled upwards.
– Cutting depth limitatio (52) deactivated.
– Inclination of the sw
locking l (23) for inclination setting is
tightened.
– Pull
–S (13) of the pulling device has been
loosened.
Cutting the wo
1. Loosen locking lever (11) of
loosen safety catch (12) .
2. Set the desired angle.
3. Tighten the locking button (11) of the
turntable.
4. Cut workpiece, as described for "Straight
cuts".
8. Commissioning
9. Operation
