ENGLISHen
14
Hazard generated by tool defects!
Prior to each use check the tool for any eventual
damage: Before cng to use the tool,
safety devices, protective devices or lightly
damaged parts must be carefully inspected
correct and proper operation. Check to see that
all moving parts work
All parts must be corr
conditions ne
operation of the unit.
Do not used any damaged or contorted s
blades.
Risk of injury by noise!
Wear hearing protection.
Danger from blocking work pieces or
work piece parts!
If blockage occurs:
1. switch machine o
2. unplug mains cable,
3. wear gloves,
4. clear the blockag
4.2 Symbols on the machine
(depends on model)
Read the operating instructions
Never place hands into
blade.
Wear protective goggl
protectors.
Never operate the tool
environment.
Laser radiation - Do not lo
beam.
4.3 Safety devices
Retractable blade guard (7)
The retractable blade guard protects against
unintentional contact with the saw blade and from
chips flying about.
Safety lock (29)
The retractable blade guard opens and the saw
can be lowered only when the safety lock is
activated.
Parallel guide/ ripping fence
The parallel guide/ ripping fence pr
workpiece ca
process. Durn, the parallel guide/
ripping fence
Make sure the adjustable fen
support the workpiece and will not interfere with
the blade or the guard. Lock using the se
(31).
See page 2.
1H
2 Chip extraction nozzle
3 Angled extraction adapter
4H
5 Cutting line ill
6 Laser beam egress point
7 Retract
8 Table ex
9T
10 Locking screw of the table width extension
11 Work clamp
12 Locking lever
13 Locking button (to exten
inclinat
14 Locking lever
15 Saw blade lock
16 Transport lock
17 Allen key /
tool storage
18 Set screw for pulling device
19 Hook for cable winding
20 Table insert
21 Safety catch for stop positions of the turntable
22 Locking handle for turntable
23 Turntable
24 On/off switch
25 On/off switch of the cutting laser
26 Speed adjustment wheel
27 On/off switch of the saw
28 Saw handle
29 Safety lock
30 Movable parallel guides/ripping
attachment)
31 Locking sc
fences
32 Locking lever (oy KGSV 72 Xact SY
33 Safety catches (only KGSV 72 Xact SYM)
34 Adjustable angle
* depends on model / equipment
Mounting the locking handle for the turntable
Insert the lock (22) into the turntable
(23) and screw in.
Attaching
The machine is supplied with a laser warni
label in German. Be
this label with the re
label in your n
Installation
The device has to be mounted on a stable
support for safe wo
– The support can either be a fixed worktop or
workbench or one of the Metabo stands (see
chapter Access
– Even when machining larger workpiece
device has to have a secure stand.
– Long workpieces
with suitable acces
Note:
For mobile use, the
plywood or coreboard panel (500 mm x 500 mm,
at least 19 mm thick) using screws. During
the panel has to be fixed to a
screw clam
1. Screw device tightly to the base (through the
holes in the feet).
2. Loosening the transp (16) : Push the
saw head slightly downwar
out transport lock (16) .
3. Swivel saw head sli
Transport
1. Swivel saw head downwards
transport lock (16) .
2. Lock the pulling dev
using the set screw (18) .
Caution!
Do not hold the saw at the protective installations
during transport.
3. Lift the tool at the carry handle (1) or at the
carry handle (4) and carry.
7.1 On/Off switch motor (27)
Switching on th
Press the on/off switch and keep pressed.
Switching off the motor:
Let go of the on/off switch.
7.2 On/off switch cutting
illumination (24)
Switching onmina
line.
Danger!
Do not direct the light beam into the eye
people or animals.
7.3 On/off switch cuttin (25)
Switching on/off of the cuttin
The cutting laser marka line on the left and a
line on the righto the cut. Make a trial cut to
become familiar with the posi
Danger!
LASER BEAM
DO NOT LOOK INTO THE BEAM
LASER CLASS 2
EN 60825-1:2007
P<1mW, λ =650nm
7.4 Setting the angle of in
Swivel the saw head upwards. Fol
lever (12) towards the front. After loosening the
locking lever (14) (swivel towards the rear), the
saw can be inclin 0° and 45° to the left
and right to the vertical.
If the lockin (12) is
the saw locks in
Press the locking button (13) during the
adjustmentr to also set ang
to 47° to the left of the vertical/ up to 47° to the
right of the vertical.
Danger!
In order for the mitre angle not to change
cutting, the lock (14) of the turntable has
to be tightened (also in the stop positions!).
7.5 Turntable
After loosening the lock (22) and
activating the safety catch (21) , the turntable can
be turned by 50° to the left or by 50° to the
for mitre cuts.
If the safety catch (21 is pushed upwards,
turntable locks in par
safety catch (21) is push
way, the locking function is deactivated.
Danger!
In order for the mitre angle not to change during
cutting, the locking han
(22)
of the turntable
to be tightened (also in the stop positi
7.6 Only KGSV 72 Xact SYM:
Symmetrica
For fast and easy sawing of
symmetrically adjustable guide syst
Pull both lo (32) upwards and loosen
the clamping mech
Push the safety catches (33) all the way
downwards, this deactivates the locking function.
Set the desired angle by position
“adjustable angle” (34) : move both halves
table (9) / parallel (30) at
the same time and adjust to the desired angle.
If the safety catches ( are in their top position,
the two halves of the table (9) /
ripping fences (30) lock at particular angle levels.
Danger!
Both locking levers (32) must be pu
downwards (also
the angle cannot change during
process.
7.7 Pulling device
Using the palso larger workpieces
with greater cross sections
pulling device can
(straight cuts, mitre cuts, slanted cuts and double
mitre cuts, and cutting of grooves).
If the pulling device is not required, lock the
pulling device in
screw (18) .
7.8 Cutting depth limitation
Together with the pulling device the cutting depth
limitation (47) permits the cutting of grooves.
Turn the set screw and fix with the counter nut
The cutting depth limitation can be deactivated, if
the parallel guide (48) is pushed towards the
5. Overview
6. Setup and transport
7. The device in detail
