Bedienungsanleitung Metabo KGT 501 (Seite 27 von 60) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

110270

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

• Make sure that nobody can get

injured by the stored machine.

Caution!

• Do not store saw unprotected

outdoors or in damp environ-

ment.

• Observe the permissible ambient

conditions (see "Technical speci-

fications").

9.5 Maintenance

Before switching ON

• Check power cable and power cable

plug for damage; if necessary have

damaged parts replaced by a quali-

fied electrician.

• Check all moving parts to see that

they can move freely across their

whole range of travel.

• Check if distance saw blade – riving

knife is 4...8 mm.

Monthly (if used daily)

• Check drive belt condition and ten-

sion, correct if necessary.

• Remove saw dust and chips with

vacuum or brush.

• Apply light coat of oil to bearings

and guide elements (not the motor

spindle and saw spindle bearings,

these are lubricated for life).

Every 300 hours of operation

• Check all screwed joints, retighten if

necessary.

• Check pull-back springs of the saw-

head (in crosscut saw mode the

sawhead must return by spring

power to its upper starting position),

replace if necessary.

• Check settings of all stops, adjust if

necessary.

• Check settings of all scales, adjust if

necessary.

In this section problems and faults are

described which you may remove your-

self. If the measures detailed here do not

solve the problem, see under "Repairs".

Danger!

Many accidents happen partic-

ularly in connection with problems

and faults. Therefore please note:

• Always unplug before servicing.

• Check that all safety devices are

operational again after each fault

service.

Motor does not run

No mains voltage

• Check cables, plug, outlet and

mains fuse.

Undervoltage relay tripped by power fail-

ure.

• Switch on again.

Motor protection tripped:

Let motor cool down for approx. 10 min-

utes, then start again.

Motor locked, e.g. by a blocked saw

blade:

• Remove cause for blocking, let

motor cool down if necessary, then

start again.

Loss of cutting performance

Saw blade blunt (possibly tempering

marks on blade body):

• Replace saw blade (see "Mainte-

nance").

Obstruction by chips

No dust collector hooked up:

• Connect dust collector.

• Remove saw dust and chips with

vacuum or brush.

Danger!

Repairs to electric tools must

be carried out by qualified electri-

cians only!

Electric tools in need of repair can be

sent to the service centre of your coun-

try. Refer to the spare parts list for the

address.

Please attach a description of the fault to

the electric tool.

For special tasks the following accesso-

ries are available at your specialist

dealer – see back cover for illustrations:

A Table Rear Extension / Table Side

Extension

for working long stock safely.

B Sliding Carriage

for convenient guiding of long

stock.

C Fence Extension

to extent the sliding carriage's

fence

D Mitre Fence

steplessly adjustable from 90°

through 45°.

E Work Clamp

for precision cuts, required for cut-

ting non-ferrous metals.

F Dust Collection Attachment

to connect a dust collector to the

saw – protects your health and

keeps the shop clean.

G Mini-Laser for Dimensioning

to indicate the line of cut on the

workpiece.

H TCT Saw Blade 250 x 2.8 / 1.8 x 30

T = 34 W

for rip and cross cuts in solid wood.

I TCT Saw Blade 250 x 2.8 / 1.8 x 30

T = 42 W

for rip and cross cuts in solid wood.

J TCT Saw Blade 250 x 2.8 / 1.8 x 30

T = 80 W

for rip and cross cuts in veneered

and faced wood core sheets.

K TCT Saw Blade 250 x 2.8 / 2.0

x 30 T = 80 TF

for cutting non-ferrous metals (alu-

minium, copper, etc.).

L Cleaning Spray

for removing resin residue and pro-

tection of metal surfaces.

M Suction Adapter

to connect a shop vacuum to the

dust collection attachment.

N Push Block Handle

to be fittet to a suitable board. For

the safe guiding of small stock.

O Work clamp

Required for precision cuts and cut-

ting of non-ferrous metals.

The machine's packing can be 100%

recycled.

Worn out power tools and accessories

contain considerable amounts of valua-

ble raw and plastic materials, which can

be recycled.

These instructions are printed on paper

produced with elemental chlorine-free

bleaching process.

10. Trouble shooting

11. Repairs

12. Available accessories

13. Environmental protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KGT 501 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info