Bedienungsanleitung Metabo KHE 22 SP (Seite 13 von 96) (Alle Sprachen)

625630

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

ENG

Metabo contact mode:

(KHE 26 Contact)

For intelligent drilling in walls with installed electric

or water lines. As soon as the inserted tool makes

contact with conductive, earthed material or live

supply cables, the machine switches off

immediately.

Metabo CODE! System

(KHE 28, KHE 26, BHE 26, KHE Partner Edition)

The Metabo CODE! System is an electronic anti-

theft device with which you can lock your Metabo

machines (if fitted with CODE!) to protect them

from abuse. Once locked, a machine can no longer

operate and therefore cannot be used by a

potential thief.

Wefore plugging in check to see that the

rated mains voltage and mains frequency,

as stated on the rating label, match with your

power supply.

7.1 Side handle installation

Wor safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(17) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (7).

Tighten the side handle in the required angle

depending on the task at hand.

8.1 Depth Stop Setting

Loosen the side handle (17). Set depth stop (7) to

the desired drilling depth and retighten the side

handle.

8.2 Switching on/off

To start the machine, press the trigger (14).

The speed can be changed at the trigger.

This machine has an electronic soft start.

For continuous operation the trigger can be locked

with the lock button (13). To stop the machine,

press the trigger again.

If switched on continuously, the machine

continues running if it is jerked out of your

hands. Therefore, always hold the

machine with both hands on the handles, stand

safely, and concentrate on your work.

8.3 Speed preselection (KHE 26 Contact)

Depending on the application, the optimum speed

is preset with the pre-selector wheel (8).

8.4 Operating mode selection

Select the desired operating mode by turning the

control knob (16). To turn, push the stop (15).

twist drilling

hammer drilling

(only with use of hammer drill chuck)

chiselling

(KHE 28, KHE 26 Contact,

KHE 26,

KHE 22 SP,

KHE 24 SP,

KHE 26 SP, KHE Partner Edition)

(only with use of hammer drill chuck)

In chisel mode the chisel is locked to be twist-proof.

To position the chisel for the particular application,

set the control knob (16) between and

When a chisel is fitted, only operate

the machine in the chiselling operating

mode.

Avoid levering movements of the machine

when a chisel is fitted.

8.5 Selection of direction of rotation

Do not actuate the rotation selector

switch (12) unless the motor has

completely stopped.

Select direction of rotation:

R = clockwise

L = counter-clockwise

8.6 Drill chuck change

(not KHE 22 SP, KHE 24 SP, KHE 26 SP,

BHE 22, BHE 20 SP)

When changing chucks make sure that

the spindle is clean. Grease spindle lightly

if required.

Removing the chuck:

Turn chuck lock (5) in direction indicated by arrow

against the stop (a) and pull it off the spindle (b).

7Start of Operation

8Use

17026895_0308 BHE_Gu incl RU.book Seite 13 Montag, 31. März 2008 8:58 08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KHE 22 SP Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info