Bedienungsanleitung Metabo KHE 2443 (Seite 8 von 49) (Alle Sprachen)

625637

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

ENGLISHen

Australia: Always use a residual current

device (RCD) protected supply with a

rated residual current of 30 mA or less.

6.1 Side handle installation

For safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(1) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (3).

Tighten the side handle in the required angle

depending on the task at hand.

7.1 Depth Stop Setting

Loosen the side handle (1). Set depth stop (3) to the

desired drilling depth and retighten the side handle.

7.2 Switching on/off

To start the machine, press the trigger (6).

The speed can be changed at the trigger.

For continuous operation the trigger can be locked

with the lock button (5). To stop the machine, press

the trigger again.

If switched on continuously, the machine

continues running if it is jerked out of your

hands. Therefore, always hold the machine

with both hands on the handles, stand safely,

and concentrate on your work.

7.3 Operating mode selection

Select the desired operating mode by turning the

control knob (8). To turn, push the stop (7).

Drilling

Hammer drilling

Chiselling

(KHE 2443 only)

In chiselling mode, the chisel is locked so that it

cannot turn.

To position the chisel for a particular application, set

the switch button (8) between and .

When a chisel is fitted, only operate the

machine in the chiselling operating mode

Avoid levering with the machine when a

chisel is fitted.

7.4 Setting the direction of rotation,

engaging the transporting safety device

(switch-on lock)

Do not activate the rotation selector switch (4)

unless the motor has completely stopped.

See page 2.

R=Clockwise setting

L = Counter-clockwise setting

Tool Change with SDS Chuck

Before fitting, clean tool shank and

apply special grease (accessories

order no. 6.31800)! Use only SDS-plus tools.

Inserting the tool:

Turn the tool while inserting, until it engages.

The tool is automatically locked.

Removing the tool:

Turn tool lock (2) in direction indicated by arrow

(a) and remove the tool (b).

The vent slots of the machine should be cleaned

from time to time.

If the trigger (6) can not be depressed, check to see

that the direction of rotation selector switch (4) is

fully set to the R or L position.

Use only genuine Metabo accessories.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline

7. Use

8. Maintenance

9. Trouble Shooting

10. Accessories

11. Repairs

12. Environmetal Protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KHE 2443 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info