Bedienungsanleitung Metabo KHE 28 Plus (Seite 14 von 92) (Alle Sprachen)

625623

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

ENG

Note:

To prevent the spindle from turning while

changing chucks, set the switch button (13) to

chiselling mode.

8.7 Tool change with SDS chuck

Before fitting, clean tool shank and apply

special grease (accessories order no.

6.31800)! Use only SDS-Plus tools.

Inserting the tool:

Turn the tool while inserting until it locks into place.

The tool is automatically locked.

Removing the tool:

Turn tool lock (3) in direction indicated by arrow (a)

and remove tool (b).

8.8 Tool change with keyless chuck

Use the keyless chuck when non-impact drilling in

metal, wood etc. and driving screws.

Chucking the tool

Turn sleeve (4) in the direction of "AUF, OPEN" (a).

Insert tool as deeply as possible (b) and turn sleeve

in the opposite direction, until the mechanical

resistance which can be felt is overcome.

Caution!

The tool is not yet clamped!

Keep turning the sleeve

(it must "click" when

turning)

until it cannot be turned any further -

only

now

is the tool

securely

clamped.

With a soft tool shank, retightening may be

required after a short drilling period.

Removing the tool:

Turn sleeve (4) in the direction of "AUF, OPEN",

and remove the tool.

Note:

The grating sound which may be heard after

opening the drill chuck is functional and is stopped

by turning the sleeve in the opposite direction.

If the chuck is very securely tightened:

Unplug.

Hold drill chuck using an open-end spanner at the

flats on its head, and turn the sleeve (4) vigourously

in the direction of "AUF, OPEN".

Only moderate pressure is required for hammer

drilling and chiselling. Applying a high degree of

pressure does not increase performance.

When drilling deep holes, remove the drill bit peri-

odically from the hole to remove dust.

Drill tiles and other brittle materials without impact.

Always keep the

safety coupling

(16)

clean and

free from dust.

Always keep the

spindle

(6) clean and apply a light

coating of grease. (for information on special

grease, see Accessories section: order no.

6.31800)

Keyless chuck (1)

cleaning:

After prolonged use hold the chuck vertically, with

the opening facing down, and fully open and close

it several times. The dust collected falls from the

opening. Regular use of cleaning spray on the jaws

and jaw openings is recommended.

Ventilation slits:

Clean the ventilation slits on the machine occa-

sionally.

If the trigger switch (12) cannot be depressed,

check to see that the rotation selector switch (10)

is fully set to the R or L position.

Electronic signal indicator (9):

Rapid flashing - restart protection

When power is restored after a power failure, the

machine - which is still switched on - will not start

for safety reasons. To continue operation, switch

the tool off and then on again.

Slow flashing - carbon brushes worn

The carbon brushes are almost completely worn. If

the brushes are completely worn, the machine

switches off automatically. Have an authorised

service centre replace the brushes.

9Tips and Tricks

10 Maintenance

11 Troubleshooting

17026909_0608 UHE KHE 28 Plus KHE Partner Edition.book Seite 14 Dienstag, 17. Juni 2008 3:51 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KHE 28 Plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info