Bedienungsanleitung Metabo KHE 2850 (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595381

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH en

17 Safety coupling

* depending on model

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

6.1 Assembly of the additional handle

For safety reasons, always use the additional

handle supplied.

Open the clamping ring by turning the additional

handle (16) anticlockwise. Push the additional

handle onto the collar of the machine. Securely

tighten the additional handle at the angle required

for the application.

6.2 Attaching the Depth Stop

Release wing screw (7). Insert the depth stop (8).

Retighten wing screw (7).

7.1 Depth Stop Setting

Release wing screw (7). Set the depth stop (8)

to the required drilling depth. Retighten wing

screw (7).

7.2 Switching On and Off

To start the machine, press the trigger (13).

The speed can be changed at the trigger.

The electronic soft start means that the machine

accelerates continuously up to the preselected

speed (not UHE 2250 Multi, UHE 2450 Multi,

KHE 2650).

For continuous operation the trigger can be locked

with the lock button (12). To stop the machine,

press the trigger again.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

7.3 Presetting the speed

(only applies for UHE 2250 Multi,

UHE 2450 Multi, UHE 2850 Multi)

Preset the optimum speed for the application using

the adjusting wheel (9).

7.4 Operating mode selection

Select the desired operating mode by turning the

switch button (14). To turn, push in the lock (15).

Twist drilling 1st gear

(high torque)

Only applies for UHE 2250 Multi,

UHE 2450 Multi, UHE 2850 Multi

Twist drilling 2nd gear

(high speed)

Hammer drilling

(only set if using (2) SDS chuck)

Setting the chiselling position

With this setting, turn the chisel to the

required position. Then select "Chiselling" to

secure the chisel and prevent it from

twisting.

Chiselling

(only set if using SDS chuck (2))

When a chisel is fitted, only operate the

machine in the chiselling operating mode .

Avoid levering with the machine when a chisel

is fitted.

7.5 Selecting the direction of rotation

Do not activate the rotation selector switch

(11) unless the motor has completely stopped.

Selecting the direction of rotation:

R=clockwise

L = counter-clockwise

7.6 Drill chuck change

When changing chucks, make sure that the

spindle is clean. Apply a light coating of grease

to the spindle. (for information on special grease,

see Accessories section: order no. 6.31800)

Only attach the Metabo chuck provided.

Removing the chuck:

Turn chuck lock (5) as far as it will go (a) in the direction

indicated by the arrow, and remove chuck (b).

6. Initial Operation

7. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KHE 2850 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info