625638
12
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
12
ENGLISH
ENG
When a chisel is fitted, only operate
the machine in the chiselling operating
mode. .
Avoid levering movements of the machine
when a chisel is fitted.
Hammer drilling and chiselling with
clockwise rotation only.
8.4 Selection of direction of rotation
Do not actuate the rotation selector
switch (8) unless the motor has
completely stopped.
Select direction of rotation:
R=clockwise
L = counter-clockwise
8.5 Drill chuck change
When changing chucks make sure that
the spindle is clean. Grease spindle lightly
if required.
Removing the chuck:
Turn chuck lock (3) in direction indicated by arrow
against the stop (a) and pull it off the spindle (b).
Replacing the chuck:
Place chuck onto spindle (5) (a). Turn chuck lock
(3) in direction indicated by arrow (b) until chuck
slides fully onto the spindle, then release the
chuck lock.
Check to see that the chuck is properly seated.
Note:
To keep the spindle from turning while
changing chucks, set the control knob (9) to
chiselling.
8.6 Tool Change with SDS Chuck
Before fitting, clean tool shank and
apply special grease (accessories
order no. 6.31800)! Use only SDS-Plus tools.
Inserting the tool:
Turn the tool while inserting, until it engages.
The tool is automatically locked.
Removing the tool:
Turn tool lock (2) in direction indicated by arrow (a)
and remove the tool (b).
8.7 Tool change with keyless chuck
(accessory)
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
Chucking the tool:
Turn sleeve towards "AUF, RELEASE" (a). Insert
tool as deeply as possible (b) and turn sleeve in the
opposite direction, until the noticeable mechanical
resistance is overcome.
Caution! The tool is not
yet clamped!
Keep turning the sleeve
(it must "click" when
turning)
until it cannot be turned any further -
only
now
is the tool
securely
clamped.
With a soft tool shank, retightening may be required
after a short time of drilling.
17024652_0308 KHE 32.book Seite 12 Dienstag, 11. März 2008 11:23 11
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo KHE 32 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info