625624
13
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
ENGLISH
13
ENG
8.1 Depth Stop Setting
Loosen the additional handle (15). Set depth stop
(7) to the desired drilling depth and retighten addi-
tional handle.
8.2 Switching On and Off
To start the machine, press the trigger switch (12).
The speed can be changed using the trigger
switch.
The electronic soft start means that the machine
accelerates continuously up to the pre-selected
speed.
For continuous operation the trigger switch can be
locked using the lock button (11). To stop the
machine, press the trigger switch again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
8.3 Speed preselection
(only applies for UHE 28 Plus)
Preset the optimum speed for the application
using the adjusting wheel (8).
8.4 Operating mode selection
Select the desired operating mode by turning the
switch button (13). To turn, push in the lock (14).
Twist drilling 1st gear
(high torque)
Only applies for UHE 28 Plus
Twist drilling 2nd gear
(high speed)
Hammer drilling
(only with use of SDS
chuck) (2)
Chiselling
(only with use of SDS
chuck) (2)
In chiselling mode, the chisel is locked so that it
cannot turn. To position the chisel for a particular
application, set the switch button (13) between
and .
When a chisel is fitted, only operate the
machine in the chiselling operating mode
.
Avoid levering with the machine when a
chisel is fitted.
8.5 Selection of direction of rotation
Do not activate the direction switch (10)
unless the motor has completely stopped.
Selecting the direction of rotation:
R = Clockwise
L = Anticlockwise
8.6 Drill chuck change
When changing chucks, make sure that the
spindle is clean. Apply a light coating of
grease to the spindle. (for information on special
grease, see Accessories section: order no.
6.31800)
Only attach the Metabo chuck provided.
Removing the chuck:
Turn chuck lock (5) as far as it will go (a) in the
direction indicated by the arrow, and remove
chuck (b).
Replacing the chuck:
Place chuck onto spindle (6) (a). Turn chuck lock
(5) in the direction indicated by the arrow (b) until
chuck slides fully onto the spindle. Then release
the chuck lock.
Check to see that the chuck is properly seated.
8Use
b
a
b
a
17026909_0608 UHE KHE 28 Plus KHE Partner Edition.book Seite 13 Dienstag, 17. Juni 2008 3:51 15
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo KHE Partner Edition wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info