Bedienungsanleitung Metabo KS 254 Plus (Seite 24 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

451459

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

2.9

KS 250

Danger!

Do not use cleaning agents (e.g. to remove

resin residue) that could corrode the light

metal components of the saw; the stability of

the saw would be adversely affected.

6. Put on inner blade collar –

observe direction of rotation: The chamfered

side must point towards the motor!

7. Fit a fresh saw blade –

observe direction of rotation: if viewed from the

left-hand (opened) side, the indicating arrow on

the saw blade must point in a clockwise direc-

tion!

Danger!

Use only suitable saw blades (see "technical

specifications") – when using unsuitable or

damaged blades parts could be explosive-

like hurled from it by centrifugal force.

Do not use:

- saw blades made of high speed steel

(HSS);

- saw blades with visible damage;

- cut-off wheel blades.

Danger!

- Fit saw blade only using genuine parts.

- Do not use loose-fitting reducing rings; the

saw blade could work loose.

- Saw blades have to be fitted such that they

do not wobble or run out of balance and

cannot work loose during operation.

8. Slide on the outer blade collar –

observe direction of rotation: The chamfered

side must face away from the saw blade!

9. Put washer on.

10. Screw in arbor bolt (left-hand thread!) and

tighten fingertight only.

To lock the saw blade in position, depress the

lock knob and turn the saw blade with the other

hand until the lock engages.

Danger!

- Do not extent arbor bolt tightening wrench.

- Do not tighten arbor bolt by hitting on the

wrench.

- After tightening the arbor bolt release the

lock knob such that the blade can turn

freely.

11. Guide blade guard over the bare side of the saw

blade.

12. Turn the saw blade guard mounting plate clock-

wise – the left hand screw (A) must be in the

oblong hole behind the small metal lug.

13. Align the mounting plate so that the right-hand

screw (B) can be screwed in.

14. Tighten both screws (A) and (B).

15. Unscrew guide screw with bushing (C).

16. Swing guide lever down and screw the guide

screw with bushing (C) through the oblong hole

of the guide lever, back in.

17. Check functioning. To do so, swing the sawhead

lock down and lower the sawhead:

- The retractable blade guard must release the

saw blade when the sawhead is swung down,

without touching other parts.

- When lifting the saw head up to its rest posi-

tion, the retractable blade guard must auto-

matically cover the saw blade.

Sawhead tilt stop setting

In order to position the sawhead exactly vertically

and at 45° for bevel cuts, the sawhead tilt stops

need to be set:

1. Swing sawhead down and lock with locking pin.

2. Loosen sawhead tilt lock lever on rear of saw.

3. Set the saw blade to exactly 90° against the

turntable, using an mitre square.

4. If necessary, loosen the counter nut on the 90°

stop screw (grey arrow) and set stop screw so

that the sawhead makes contact with it at the

90° position. Retighten counter nut.

5. Repeat step three and four for the 45° stop

screw (black arrow) with a 45° mitre square.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KS 254 Plus Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info