Bedienungsanleitung Metabo KS 66 PLUS (Seite 16 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595374

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

ENG

23 Adjusting screw (adjust saw blade angle)

24 Lock nut (adjust saw blade angle)

25 Hexagon spanner

26 Locking screw (

for setting cutting depth

)

27 Scale (depth of cut)

28 Spindle locking button

* equipment-dependent

• Metabo S-automatic safety clutch:

If the tool jams or catches, the power supply to

the motor is restricted. Due to the strong force

which can arise, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

• Mechanical safety brake for stopping saw blade

quickly when switching off the machine (KSE 68

Plus only).

• Hard-wearing guide plate made from light-

weight cast magnesium

• Vibration-damping, non-slip rubber coating in

grip area.

• Double-guided parallel stop, can be used on the

left and right for greater flexibility

• Lock preventing inadvertent machine start-up

• Lubricating system extends the service life of

the gearbox

• Vario Tacho Constamatic (VTC) full-wave elec-

tronics for stepless speed adjustment. The

machine speed stays constant automatically

under load (only KSE 68 Plus)

• Setting wheel for speed preselection (only KSE

68 Plus)

• Electronic function monitoring the coil tempera-

ture protects against overload. Light signal

when the machine begins to overload (only KSE

68 Plus)

• External dust extraction possible: option of

connecting an extraction unit

• Carbon brushes for protecting the motor

• Guide rail available as an accessory (order no.

6.31213)

• Tool-less fine machine adjustment when used

on guide rail 6.31213

Before plugging in, check to see that the

rated mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Pull the plug out of the plug socket before

any adjustments or servicing are performed.

7.1 Setting splitting wedge

The splitting wedge (16) prevents the wood from

closing behind the saw blade and jamming it while

the machine is in operation. This could otherwise

lead to recoiling.

The splitting wedge must be set in such a

way that the distance between its inner curve

and the toothed ring on the saw blade is no greater

than 5 mm. Set the splitting wedge so that the

lowest point of the saw blade does not protrude by

more than 5 mm below the bottom edge of the

splitting wedge. See illustration on page 2.

To adjust, loosen the hex screw (15), set the right

distances to the saw disc and tighten the hex

screw again.

7.2 Setting depth of cut

Loosen the locking screw (26). Raise or lower the

motor section against the guide plate (1). Read the

depth of cut that has been set from the scale (27).

Tighten the locking (26)screw again.

It is advisable to set the depth of cut in such a way

that no more than half of each tooth on the saw

blade juts out under the workpiece. See illustration

on page 3.

The clamping power of the locking screw (26) can

be adjusted. Unscrew the screw on the lever to do

this. Remove lever and mount offset anticlockwise.

Secure with screw. When doing this, note that the

cutting depth setting device moves freely when the

lever is open.

7.3 Slanting saw blade for diagonal cuts

Loosen the two locking screws (6) to make the

setting. Tilt the motor section against the guide

plate. Read the angle which has been set from the

scale (4). Retighten the front and then the rear

locking screw (6).

7.4 Correcting the saw blade angle

The

saw blade angle is set ex works.

If, at 0°, the saw blade is not at right angles to the

guide plate: release locking screws (6). Release

lock nut (24) and correct saw blade angle with

adjusting screw (23). Then retighten the lock nut.

Retighten both locking screws (6).

7.5 Rotational speed preselection

Select the speed at the setting wheel (14). For

recommended speeds, see page 2.

6 Special Product Features

7 Initial Operation, Setting

17026944_0209 KSE 6x Plus MG-Guss.book Seite 16 Montag, 26. Januar 2009 2:08 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo KS 66 PLUS Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info