Bedienungsanleitung Metabo LSV 5-225 (Seite 10 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

600597

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISHen

15 Sanding head

16 Service flaps

17 Screws of the service flaps

18 Locking screw for support plate

19 Washer

20 Screw of the eccentric

21 Eccentric

22 Shaft

* depending on the model / features

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

type plate match your power supply.

Always install an RCD with a maximum trip

current of 30 mA upstream.

Pull the plug out of the plug socket before any

adjustments or servicing are performed.

6.1 Shorten or extend handle bar (LSV 5-

225 Comfort)

Disassemble handle bar

See figure A.

1. Lift locking bow (6)

2. Swivel the hook holder (7) downwards.

3. Pull apart the handle bars (8).

See figure A.

Assemble handle bars

See figure B.

1. Put together (8) the handle bars as shown.

2. Swivel the hook holder upwards (7) until the

stop.

3. Fold the locking bow (6) downwards until it

touches the handle bar.

4. Check for secure connection. If the handle bars

cannot be connected securely, the tension has

to be adjusted. See chapter maintenance.

6.2 Installation of sanding sheet

Sanding sheet with velcro-type fastening

Simple attachment and removal thanks to the

velcro-type fastening. Simply press on the sanding

sheet so that the holes in the sanding sheet (2) are

aligned with the support plate (1).

6.3 Dust extraction

To optimise the dust extraction performance, fit the

sanding sheet (2) so that the holes on the sanding

sheet are aligned to the support plate (1).

For optimum vacuum power turn the brush rim as

shown (until the stop): Brush rim (3) and rubber lip

(4) completely encompass the support plate (1) .

Connect a suitable extraction device to the extractor

connection piece (14).

When sanding prepared surfaces with high dust

generation we recommend using an all-purpose

vacuum cleaner with automatic filter cleaning for

continuous use (e.g. ASR 35 L ACP, ASR 35 M

ACP).

Note: the bush 316062390 is particularly suited as

it is secured against slipping with a bayonet closure.

Fix the bush 316062390 to the extraction hose as

follows: Remove the bush of the suction hose from

the suction hose (left-hand thread) and fix special

bush (left-hand thread).

6.4 Sanding near edges

When sanding near edges turn the brush rim (3) in

such a way that the support edge (5) can be guided

along the workpiece edge.

Use only in assembled state. Do not switch on

the machine if tool parts are missing or

defective.

7.1 Switching on/off of the machine

Switch the machine on/off at the switch (11) .

I=On

0=Off

First switch on the machine and then bring the

sanding plate to the work surface.

If the requirements for the quality of the sanding

result are very high, we recomment to first bring the

sanding plate to the work surface and then switch

on the machine.

7.2 Setting speed

Set the speed at the setting wheel (12). This can

also be done during operation.

The best way to determine the ideal setting is

through a practical trial.

7.3 Switching on / off of the LED light

Use the switch (10) to switch the LED ligth (9) on or

off.

(The LED light is on only when the motor is running.)

I=On

0=Off

Pull the plug out of the plug socket before any

servicing or cleaning are performed.

Clean the machine regularly. This includes

vacuum cleaning the ventilation louvres on the

motor.

Clean the support plate (1) as required (vacuum

off the dust). This increases the service life of the

velcro-type fastening.

Remove blockages in the sanding head (15)

-Note:

left and right cleaning flap (16) are not

interchangeable, therefore do not interchange!

Remove fixing screws of the service flaps (17),

remove service flaps and put aside.

- Vacuum with the crevice nozzle of an extraction

device, if required, ensure clear passage using a

wire.

- If required, remove support plate (1) and vacuum

the extraction channels underneath and ensure

clear passage.

6. Commissioning

7. Use

8. Cleaning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo LSV 5-225 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info