Bedienungsanleitung Metabo SBE 730 (Seite 15 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

511046

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH en

8.11 Unscrew the chuck (when driving screws

without the chuck or for use with attach-

ments)

Fig. L, M, or N

Note for Fig. M, N:

Release by tapping lightly with a

rubber hammer, as shown, and unscrew.

Note:

If a bit clamping bush (order no. 6.31281) is

attached, the screwdriver bit inserted in the

hexagon socket of the spindle is held in place.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with

the opening facing down, and fully open and close it

several times. The dust collected falls from the

opening. The application of cleaning spray to the

jaws and jaw openings at regular intervals is recom-

mended.

Electronic signal display (10):

Rapid flashing - restart protection

(SBE 1000, SBE 1100 Plus)

When power is restored after a power failure, the

machine - which is still switched on - will not start for

safety reasons. Switch machine on and off again.

Slow flashing - carbon brushes worn

(SBE 1100 Plus)

The carbon brushes are almost completely worn. If

the brushes are completely worn, the machine

switches off automatically. Have the brushes

replaced by an authorized service centre.

Permanently lit - overload

(SBE 1100 Plus)

If the machine is subject to long periods of contin-

uous overloading, the power input of the machine is

limited. This prevents the further unauthorized

heating of the motor.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

For a complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

Fig. O.

We reserve the right to make technical

improvements.

=Rated input

=Power output

* =No-load speed

*=Load speed

max. dia. =Max. solid drill diameter

s max =Max. impact rate

b =Chuck capacity

G=Spindle thread

H =Spindle with hexagon socket

m=Weight

D =D=Collar diameter

Measured values determined in conformity with

EN 60745.

Machine in protection class II

~ Alternating current

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

* Energy-rich, high-frequency interference can cause

fluctuations in speed. The fluctuations disappear,

however, as soon as the interference fades away.

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with

the values emitted by other power tools. The actual

values may be higher or lower, depending on the

particular application and the condition of the tool or

power tool. In estimating the values, you should also

include work breaks and periods of low use. Based

on the estimated emission values, specify protective

measures for the user - for example, any organisa-

tional steps that must be put in place.

Vibration total value (vector sum of three directions)

determined in accordance with EN 60745:

h, ID

=Vibration emission value (impact drilling

into concrete)

h, D

=Vibration emission value

(drilling into metal)

h,ID

h,D

=Uncertainty (vibration)

Typical A-effective perceived sound levels:

=Sound pressure level

=Acoustic power level

, K

= Uncertainty

Wear ear protectors!

9. Cleaning, Maintenance

10. Troubleshooting

11. Accessories

12. Repairs

13. Environmental Protection

14. Technical Specifications

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo SBE 730 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info