Bedienungsanleitung Metabo SE 2500 (Seite 10 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595104

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH en

When the depth stop (12) is inserted, the insertion

depth changes by 0.25 mm per notch. If screw

insertion has to be deeper: Insert stop sleeve If the

screw insertion is too deep: Unscrew stop sleeve.

Removal of the depth stop (12) does not alter the

set screw insertion depth. After refitting, work can

continue at the same insertion depth.

When screwing in crosshead screws, press

the machine with the screwdriver bit (13) firmly

against the screw until the screw is fully inserted;

otherwise the bit could slip out of the cross recess

and damage the material.

7.5 Working without depth stop (12)

Adapt the speed of the screwing process by

carefully pressing in the trigger switch.

When the screwing process is complete, switch off

the machine by releasing the trigger switch (3).

7.6 LED lamp (depending on the model)

For working in badly lit areas. The LED light (6)

lights up when the machine is switched on.

Press the machine firmly against the screw until the

screwing process is complete.

This is particularly important when inserting dry wall

screws (with coarse threads) in gypsum

plasterboards because the large thread pitch of the

screws means that they are very quickly inserted.

If the stop sleeve (17) is stiff, it can be removed to

clean the thread.

If the screwdriver bit (13) is fitted very firmly in the bit

holder (14): remove the screwdriver bit with a pair of

pliers.

9.1 Only for cordless machines; the

machine's multifunctional monitoring

system

If the machine switches off automatically, the

machine electronics have activated automatic

protection mode.

In spite of this protective function, overloading

is still possible with certain applications and

can result in damage to the machine.

Causes and remedies:

1. Battery pack almost flat (the electronics

prevent the battery pack from discharging totally

and avoid irreparable damage).

If one LED is flashing, the battery pack is almost

flat. (10) If necessary, press the (11) button and

check the LEDs (10) to see the charge level. If

the battery pack is almost flat, it must be

recharged.

2. Long continuous overloading of the machine will

activate the temperature cut-out.

Leave the machine or battery pack to cool.

Note:

If the battery pack feels very warm, the

pack will cool more quickly in your "AIR

COOLED" charger.

Note:

The machine will cool more quickly if you

operate it at idling speed.

3. If the current is too high (for example, if the

machine seizes continuously for long periods),

the machine switches off.

Switch off the machine at the trigger switch (3).

Then continue working as normal. Try to prevent

the machine from seizing.

ENG

Disconnect the mains plug or remove the battery

pack from the machine before starting any

maintenance work.

Remove the depth stop (12) regularly and clean it

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of the

power tool.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

A Magazine screw attachment 6.31618

B Screwdriver bits (length: 25 mm)

Recommendation: only use screwdriver bits

with plug-in ends of this type:

C Battery chargers: ASC Ultra, ASC 15, ASC 30

and others.

D Battery packs 18 Volt: 5.2 Ah (6.25592); 4.0 Ah

(6.25591); 2.0 Ah (6.25596)

See www.metabo.com or the catalogue for a

complete range of accessories.

Repairs to electrical tools must ONLY be carried out

by qualified electricians!

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. See

www.metabo.com for addresses.

You can download a list of spare parts from

www.metabo.com.

8. Tips and Tricks

9. Troubleshooting

10. Maintenance

11. Accessories

12. Repairs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo SE 2500 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info