Bedienungsanleitung Metabo STA 18 LTX 140 (Seite 11 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595067

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH en

- Press the button (16); the LEDs indicate the

charge level. (15)

- (15)If one LED is flashing, the battery pack is

almost flat and must be recharged.

7.9 Removing or replacing the battery pack

Fig. A

To remove: Press the battery pack release (13)

button and pull the battery pack (14) upwards

To fit:Slide in the battery pack (14) until it engages.

8.1 Chip blower

Fig. A

Turn the button (8) to turn on (symbol ) or off.

8.2 Set the pendulum motion

Fig. A

Set the required pendulum motion using the adjust-

ment lever (7).

Position "0" = pendulum motion is switched off

. . .

Position "III" = maximum pendulum motion

Recommended settings:

Fig. G.

The best way to determine the ideal setting is

through a practical trial.

8.3 Set the maximum speed/stroke

Fig. A

Set the machine to maximum speed using the

setting wheel (12). This is also possible during oper-

ation.

Setting wheel position "A" = automatic start-up

system: during the sawing process, the speed auto-

matically increases to the maximum speed.

Recommended settings:

Fig. G.

The best way to determine the ideal setting is

through a practical trial.

8.4 Switching on/off, continuous operation

Fig. A

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid switching on the machine accidentally:

always switch it off when the battery pack is

removed from the machine.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore always hold the machine with

both hands using the handle provided, stand

securely and concentrate.

Switching on: Push the slide switch (9) forward.

For continuous activation, now tilt downwards until

it engages.

Switching off: Press the rear end of the slide

switch (9) and release.

8.5 LED light

Fig. A

For working on dimly lit areas. The LED lights (4)

light up when the machine is switched on.

If the LED light is flashing, see chapter 10.

8.6 Note on use

Fig. E

Plunging You can plunge the jigsaw blade into

workpieces made from thin, soft materials without

needing to drill a hole beforehand. Only use short

saw blades. Only at 0° angle setting.

Set the adjustment lever (7) to the "0" position

(pendulum motion is deactivated). Position the

jigsaw with the front edge of the footplate (10) on the

workpiece. Hold the operating jigsaw firmly and

guide slowly downwards. Once the saw blade has

penetrated the workpiece, the pendulum motion

can be activated.

Clean the machine regularly. This includes

vacuum cleaning the ventilation louvres on the

motor.

(19) Clean the saw blade clamping fixture regularly

and thoroughly by applying a jet of compressed air.

If necessary, clean the openings behind the saw

blade support roller (18).

Apply a drop of oil to the saw blade support roller

(18) from time to time.

If necessary, adjust the clamping force of the clamp

lever (22)

(

Fig. D): Release the safety screw

(23) and turn the clamping force screw (24) (turning

the screw anti-clockwise increases the clamping

force). Tighten the safety screw (23).

The LED light (4) is flashing SLOWLY and the

machine has been switched off automatically.

The machine switches off if it is overloaded for an

extended period or if the saw blade is jammed.

Switch off the machine at the slide switch (9).

Switch it on again and continue to work as normal.

Avoid any additional overloading or jamming.

The LED (4) is flashing quickly and the machine

is not running. The restart protection is active. The

machine will not start if the battery pack is inserted

while the machine is on. Switch the machine off and

on again.

Only use original Metabo accessories

Fig. F.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

AChargers

B Battery pack

C Circular-cutting and parallel guide

8. Use

9. Cleaning, Maintenance

10. Troubleshooting

11. Accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo STA 18 LTX 140 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info