Bedienungsanleitung Metabo STE 90 SCS (Seite 11 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595392

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISHen

13 Adjustment lever for pendulum motion

Switch button

on the

chip blower

15 Sliding switch

16 Hexagon spanner

17 Setting wheel for speed adjustment

18 Extractor connection piece

19 Screw for adjusting the footplate

20 Curved support plate indicating preset cutting

angle

* depending on equipment/not in scope of delivery

Before plugging in, check to see that the rated

mains voltage and mains frequency, as stated

on the rating label, match your power supply.

Australia: Always use a residual current device

(RCD) protected supply with a rated residual

current of 30 mA or less.

Never operate the machine without a saw

blade.

6.1 Fitting the anti-splintering footplate

insert

Danger of injury due to the sharp jigsaw blade.

Remove the saw blade

before fitting (8) the anti-

splintering footplate insert.

Turn the machine over so that the footplate faces

upwards. Insert the anti-splintering footplate from

the front,

ensuring the following:

•

The smooth side of the footplate faces upwards.

•

The slot is facing to the rear (towards the mains

cable).

If you wish to work with the protective plate attached

(see chapter Accessories 10.), fit the anti-

splintering footplate insert in the protective plate..

6.2 Sawing with a guiding device for straight

cuts (SCS)

The metal guide (5) of the guide element (6) dips

into the kerf and stabilises the machine to ensure

even straighter cuts.

Removing the guide element:

- Hold the machine with the footplate down.

- Press the unlocking key. The guide element thus

falls out of its retainer in the footplate.

(Should the guide element not fall out by itself, you

can insert the hexagon spanner (16) into the guide

element hole and remove it in this way).

Inserting the guide element:

For straight cuts, insert the guide element so

that the metal guide (5) protrudes under the

footplate.

For diagonal and curved cuts, insert the

guide element so that the metal guide (5) fits

into the footplate and is not visible.

- With the unlocking key pressed, insert the guide

element into the footplate.

Note:

It can only be inserted if the hole in the guide

element is facing backwards (towards the mains

cable).

6.3 Inserting the saw blade

Danger of injury due to the sharp jigsaw blade.

After stopping work, the jigsaw blade may still

be hot. Wear protective gloves.

Use a saw blade that is suitable for the material

being sawn.

- Turn the clamping lever (1) forwards to the stop

and hold in place.

- Insert the saw blade (4) up to the stop. Ensure that

the saw teeth are facing forwards and the blade is

seated correctly in the groove on the saw blade

support roller (3).

- Release the clamping lever (1). (It returns to its

initial position by itself. The saw blade is now

securely tightened).

6.4 Attaching / Removing the protective cap

Attachment: Push on the protective cap (11) from

the front until it engages

Removal: Grip both sides of the protective cap

(11), lift slightly, then pull forwards and remove.

6.5 Sawing with dust extraction

- Connect a suitable extraction device to the

extractor connection piece (18). Use a suction

hose with a 30 mm connector diameter.

- Attach the protective cap (11) for maximum

extraction efficiency.

- Switch off the chip blower (see chapter 7.1).

6.6 Sawing without dust extraction

- Work with the protective cap (11) removed

(see Removal chapter 6.4).

6.7 Diagonal cuts

Remove the protective cap (11), anti-splintering

footplate insert (8) and extraction hose. These parts

cannot be used for diagonal cuts.

- Remove the guide element (6) (see section 6.2).

- Slacken the screw (19).

- Slid the footplate (9) forwards slightly and turn.

- Then slide the footplate (9) forwards or backwards

and engage in one of the detents (the detents can

be viewed through the semicircular opening at the

rear of the footplate (9).) The preset angle is

indicated on the curved support plate (20) on the

footplate. Adjust to different angles using an angle

gage.

- Tighten the screw (19) again.

- Insert the guide element (6) once more

(see section 6.2).

6.8 Sawing close to the wall

Remove the protective cap (11), anti-splintering

footplate insert (8), circular-cutting and parallel

guide. These parts cannot be used when sawing

close to the wall.

- Remove the guide element (6) (see section 6.2).

- Slacken the screw (19) until the footplate (9) can

be raised slightly.

- Raise the footplate (9) slightly and slide

backwards up to the stop.

- Tighten the screw (19) again.

6. Commissioning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo STE 90 SCS Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info