Bedienungsanleitung Metabo STEB 140 (Seite 11 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595397

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH en

system: during sawing, the speed automatically

increases to the maximum speed.

Recommended settings:

Fig. H.

The best way to determine the ideal setting is

through a practical trial.

8.4 Switching on/off, continuous operation

Fig. A

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore always hold the machine with

both hands using the handle provided, stand

securely and concentrate.

STE 140, STE 140 Plus:

Switching on: Push the slide switch (8) forward

(continuous operation).

Switching off: Push the slide switch (8) back.

STEB 140, STEB 140 Plus:

Switching on: Press the trigger (13). Press the

trigger more to increase the speed (up to preset

maximum speed, see chapter 8.3).

Switching off: Release the trigger (13).

Continuous operation: For continuous operation,

the pressed trigger (13) can be locked using the

lock button (14). To stop the machine, press the

trigger (13) again.

8.5 LED light (depending on fittings)

Fig. A

For working on dimly lit areas. The LED light (3)

lights up when the machine is connected and in

motion. The LED light switches off after a few

seconds when the machine is not in motion.

If the LED light is flashing, see chapter 10.

8.6 Note on use

Fig. F

Plunging You can plunge the jigsaw blade into

workpieces made from thin, soft materials without

needing to drill a hole beforehand. Only use short

saw blades. Only at 0° angle setting.

Set the adjustment lever (6) to the "0" position

(pendulum motion is deactivated). Position the

jigsaw with the front edge of the footplate (9) on the

workpiece. Hold the operating jigsaw firmly and

guide slowly downwards. Once the saw blade has

penetrated the workpiece, the pendulum motion

can be activated.

Clean the machine regularly. This includes

vacuum cleaning the ventilation louvres on the

motor.

Clean the saw blade clamping fixture regularly and

thoroughly by blowing with compressed air.

If necessary, clean the openings behind the saw

blade support roller (16).

Apply a drop of oil to the saw blade support roller

(16) from time to time.

STE 140 Plus, STEB 140 Plus: If necessary, adjust

the clamping force of the clamp lever (20)

(

Fig. E): Release the safety screw (22) and turn the

clamping force screw (23) (turning the screw anti-

clockwise increases the clamping force). Tighten

the safety screw (22).

Only for STE 140 Plus, STEB 140 Plus:

The LED (3) is flashing and the machine is

not running. The restart protection is active.

If the mains plug is inserted with the machine

switched on, or if the current supply is restored

following an interruption, the machine does not start

up. Switch the machine off and on again.

Only use original Metabo accessories

Fig. G.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

A Attaching the circular-cutting and parallel

guide

For sawing circles (dia. 100 - 360 mm) and making

cuts parallel with edges (max. 210 mm).

Attach the circular-cutting guide (

Fig. G-I)

- Slide the rod on the circular-cutting and parallel

guide sideways into the footplate (centre point (c)

faces downwards).

- Set the desired radius (d).

- Tighten screw (b).

Attach parallel guide (

Fig. G-II)

- Slide the rod on the circular-cutting and parallel

guide sideways into the footplate (centre point (c)

faces upwards).

- Set the dimension (e)

- Tighten screw (b).

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

9. Cleaning, Maintenance

10. Troubleshooting

11. Accessories

12. Repairs

13. Environmental Protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo STEB 140 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info