Bedienungsanleitung Metabo TBP 4000 M (Seite 12 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Finnisch)

600794

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

 Required space approx. 100 mm

diameter.

 The pump must not be submerged

deeper into water then stated in the

"Technical Specifications".

 The pump' suction inlet must not be

positioned in the well's filtration area

and not near the bottom. Position

the pump as high as possible in the

well, but at least 2 m below the

water level.

 In case the pump is not operated in

a tube well the operator must ensure

that no foreign matter is taken in.

Caution! 

Do not lift pump at cable or dis-

charge hose; both are not designed

for the tensile load by the weight of

the pump.

1. Lower pump to the bottom of the

fluid container. Use a sturdy rope

fastened to the pump head to lower

the pump.



The pump can also be operated

when suspended by a rope.

2. Plug the power cable in.

6.1 Switching ON and OFF

 To start the submersible pump plug

the power cable in.

 Unplug to stop the pump.

Caution! 

At too low a water level the

deep well pump runs dry and will be

damaged or destroyed.

When operating the pump always

make sure that the water level is suffi

cient and dry running is not possible.

Damage caused by running dry is not

covered by the manufacturer's war

ranty!

Overload protection

This submersible pump has an overload

protection which automatically turns the

motor off in case the pump is over-

loaded. 

If the overload protection has tripped:

1. Unplug.

2. Remove cause for the overload (see

"Care and Maintenance").

6.2 Pump Characteristic

Curve

The pump characteristic curve shows

which pump capacity is possible in

dependance on the delivery head.

Danger! 

Prior to all servicing:

1. Turn OFF.

2. Unplug.

3. Ensure that pressure is relieved

from the pump and connected

accessories.

Service and repair work other than

described here must be left to quali-

fied specialists.

7.1 Periodic Maintenance

In order for the deep well pump to func-

tion perfectly at any time periodic main-

tenance is required. This also applies if

the deep well pump is operated under

heavy conditions, but not turned on over

prolonged periods.

 Let the pump run periodically to

keep solids from getting stuck inside

the pump.

 Leave pump in the water if possible,

to keep residual matter from drying

inside the pump.

Yearly maintenance

1. Check pump casing and cable for

damage.

2. Rinse pump with clear water.

Remove persistant soiling, e.g.

algae desposits, with brush and

dishwashing liquid.

3. To flush the inside of the pump,

place it into a container filled with

clear water and turn ON briefly.

Cleaning the suction inlets

1. At the bottom of the lower part, in

the centre opening, is a locking for

removing the end piece.

Unscrew the three securing screws

from the locking.

2. Push all three plastic locking bars of

the locking from inside to the outside

and pull the end piece out.

3. Clean end piece with clear water

and fit it back into the pump. The

plastic locking bars must engage

with an audible click.

Cleaning the impellers

1. Loosen the screws on the upper part

of the deep weel pump and remove

the top.

Note:

If necessary you can remove the

power cable. To do so, loosen the two

screws of the cable clamp and pull off

the cable plug.

2. Completely unscrew the lower part.

3. Unscrew the hexagon nut on the

impeller shaft and pull the impellers

off.

4. Clean impellers and all accessible

inside surfaces of the casing.

Remove any fibres which may have

wound around the impeller shaft.

Remove persistant soiling with

brush and dishwashing liquid.

Caution!

When reassembling the pump

make sure the O-rings on both upper

and lower part are undamaged and

properly positioned.

5. Re-assemble the deep well pump.

7.2 Pump Storage

Caution! 

Frost damages the pump and

accessories, as both always contain

water!

 When there is danger of freezing

remove pump and accessories and

store in a frost-free location.

Danger!

Prior to all servicing:

1. Turn OFF.

2. Unplug.

3. Ensure that pressure is relieved

from the pump and connected

accessories.

8.1 Troubleshooting Guide

Pump does not run:

 No mains voltage.

 Check cables, plug, outlet and

mains fuse.

 Mains voltage too low.

 Use only extension cables with

sufficient lead cross section (see

"Technical Specifications").

6. Operation

7. Care and Maintenance

8. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo TBP 4000 M Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info